Tiny module with compass and barometer from Flywoo! If your FC board has a barometer, you need to disconnect the Baro SDA / SCL pad. Check out all our Flywoo products! Specifications Baro: BMP280 Compass QMC5883L Power supply: 3.3V-5V Communication: I2C protocol Pin: SH1.0-4 Module size: 11x15.5mm Weight: 0.6g Includes 1x Flywoo BQNANO V1.0 Compass and Barometer

Read more less

Note: The chip of GOKU GM10 V3 GPS is M10050. Only BF4.3x version firmware can use Ublox protocol. BF4.2x and earlier firmware can only use NMEA protocol But there is no difference in performance between the two protocols GOKU GM10 V3 GPS series is here!  Using the latest M10050 GNSS chip. Compared with the previous generation GM8 V2, the positioning is more accurate, and the speed of star search is faster. Check out our other GPS options, as well as the rest of our Flywoo selection! Features GPS Module, Three Module 1.0mm spacing between the 4pins patch seat Specifications Brand: FLYWOO Model: GM10 MINI V3 GPS Dimension: 18x18x4.8mm Weight: 4.7g Connector: 1.00mm spacing between the 4pins patch seat Chipset: M10050 (Tenth Generation Chip) Receiving Format: GPS, GLONASS, Galileo, BeiDou, QZSS and SBAS Default Protocol: GPS, Galileo, BeiDou Frequency: GPS L1, GLONASS L1, BeiDou B1, SBAS L1, Galileo E1 Channels: 72 Searching Channel Tracking: -162dBm Reacquisition: -160dBm Support Rate: 4800bps to 921600bps, Default 115200bps Data Level: TTL or RS-232, Default TTL level Data Protocol: BF4.3.X (UBLOX) / BF4.2.X (NMEA) Output frequency: 1Hz-10Hz，Default 10Hz Altitude: 50,000m Max Velocity: 500m/s Max Acceleration: Less than 4g VCC: DC Voltage 5V Operating temp:　-40 °C ~ +85°C Storage Temp: -40°C ~ +105°C PPS LED: yellow .PPS LED is not bright when GPS is not fixed, flashing when fixed The Module’s Pins: GND TX RX 5V Includes 1x Flywoo GOKU GM10 Mini V3 GPS 1x 100mm Cable 1x Copper Foil Wiring Diagram

Read more less

Note: The chip of GOKU GM10 V3 GPS is M10050. Only BF4.3x version firmware can use Ublox protocol. BF4.2x and earlier firmware can only use NMEA protocol But there is no difference in performance between the two protocols GOKU GM10 V3 GPS series is here!  Using the latest M10050 GNSS chip. Compared with the previous generation GM8 V2, the positioning is more accurate, and the speed of star search is faster. Check out our other GPS options, as well as the rest of our Flywoo selection! Features GPS Module, Three Module 4pins Pad, ultra-lightweight  Specifications Chipset: M10050 (Tenth Generation Chip) Receiving Format: GPS, GLONASS, Galileo, BeiDou, QZSS and SBAS Default Protocol: GPS, Galileo, BeiDou Frequency: GPS L1, GLONASS L1, BeiDou B1, SBAS L1, Galileo E1 Channels: 72 Searching Channel Tracking: -162dBm Reacquisition: -160dBm Support Rate: 4800bps to 921600bps, Default 115200bps Data Level: TTL or RS-232, Default TTL level Data Protocol: BF4.3.X (UBLOX) / BF4.2.X (NMEA) Output frequency: 1Hz-10Hz，Default 10Hz Altitude: 50,000m Max Velocity: 500m/s Max Acceleration: Less than 4g VCC: DC Voltage 3.3-5V Operating temp:　-40 °C ~ +85°C Storage Temp: -40°C ~ +105°C PPS LED: Yellow .PPS LED is not bright when GPS is not fixed, flashing when fixed The Module’s Pins: RX TX 3.3-5V GND Includes 1x Flywoo GOKU GM10 Nano V3 GPS 1x 100mm Cable 1x Copper Foil Wiring Diagram

Read more less

The Flywoo GOKU GM10 Nano V3 Micro GPS with Compass (10th Gen) is the perfect choice for reliable navigation. This GPS weighs in at just 2.8g, and its smaller design allows for increased portability and easier mounting. Enjoy precise navigation with cutting edge 10th generation technology brought you by the experts at Flywoo! Check out our other GPS options, as well as the rest of our Flywoo selection! Feature Integrated compass Using the latest M10050 GNSS chip Plug and play, no need for soldering. Compared with the previous generation GM8 V2, the positioning is more accurate, and the speed of satellite search is faster. Specifications Model: GM10 NANO V3 GPS w/compass Dimension: 12mmx17mmx5mm Weight: 2.6g Connector: 4pins Pad Electrical Characteristics Chipset: M10050(Tenth Generation Chip) Receiving Format: GPS,GLONASS,Galileo,BeiDou,QZSS and SBAS Default Protocol: GPS,Galileo,BeiDou Frequency: GPS L1,GLONASS L1,BeiDou B1,SBAS L1,Galileo E1 Channels: 72 Searching Channel Sensitivity Tracking: -162dBm Reacquisition: -160dBm Data and Update Rate Support Rate: 4800bps to 921600bps,Default 115200bps Data Level: TTL or RS-232,Default TTL level Data Protocol: BF4.3.X(UBLOX)/BF4.2.X(NMEA) Output frequency: 1Hz-10Hz，Default 10Hz Operational Limits Altitude: 50,000m Max Velocity: 500m/s Max Acceleration: Less than 4g Power consumption VCC: DC Voltage：3.3-5V Operating temp: -40 °C ~ +85°C Storage Temp: -40°C ~ +105°C Indicator PPS LED:yellow .PPS LED not bright when GPS not fixed,flashing when fixed The Module’s Pins: RX TX 3.3-5V GND Includes 1x Flywoo GOKU GM10 Nano V3 GPS w/ Compass (10th Gen) 1x 150mm Cable 1x Copper Foil Wiring Diagram GPS Rescue Mode Settings  Note: The chip of GOKU GM10 V3 GPS is M1005. Only BF4.3x version firmware can use Ublox protocol. BF4.2x and earlier firmware can only use NMEA protocol But there is no difference in performance between the two protocols BETAFLIGHT：Use firmware above 4.3.0INAV：Use the latest 6.0.0 configurator, the latest firmware above 5.0.0

Read more less

Note: The chip of GOKU GM10 V3 GPS is M10050. Only BF4.3x version firmware can use Ublox protocol. BF4.2x and earlier firmware can only use NMEA protocol But there is no difference in performance between the two protocols GOKU GM10 V3 GPS series is here!  Using the latest M10050 GNSS chip. Compared with the previous generation GM8 V2, the positioning is more accurate, and the speed of star search is faster. Check out our other GPS options, as well as the rest of our Flywoo selection! Features GPS Module, Three Module Compass With electronic compass IC QMC5883L 1.0mm spacing between the 6pins patch seat Specifications Brand: FLYWOO Model: GM10 PRO V3 GPS w/ Compass Dimension: 25x25x6mm Weight: 7.3g Connector: 1.00mm spacing between the 6pins patch seat Chipset: M10050 (Tenth Generation Chip) Receiving Format: GPS, GLONASS, Galileo, BeiDou, QZSS and SBAS Default Protocol: GPS, Galileo, BeiDou Frequency: GPS L1, GLONASS L1, BeiDou B1, SBAS L1, Galileo E1 Channels: 72 Searching Channel Tracking: -162dBm Reacquisition: -160dBm Support Rate: 4800bps to 921600bps, Default 115200bps Data Level: TTL or RS-232, Default TTL level Data Protocol: BF4.3.X(UBLOX)/BF4.2.X(NMEA) Output frequency: 1Hz-10Hz，Default 10Hz Altitude: 50,000m Max Velocity: 500m/s Max Acceleration: Less than 4g VCC: DC Voltage: 5V Operating temp: -40 °C ~ +85°C Storage Temp: -40°C ~ +105°C Includes 1x GM10 PRO V3 GPS w/ Compass 1x 150mm Cable 1x Copper Foil Wiring Diagram

Read more less

The Foxeer M10Q-250 GPS & Compass offers reliable performance with its dual-module GPS and compass system. It features fast signal acquisition and low power consumption, with the ability to track up to 22 satellites. The precision navigation capabilities ensure stable and accurate navigation, making it a great choice for racing drones and other aerial applications. Check out our other GPS options, as well as the rest of our Foxeer Collection! Features U-Blox M10050 GPS+GLONASS+BDS QMC5883 Compass Dual Protocol  2D ACC 1.5m Precise Positioning Specifications Chip: M10(10th Generation Chip) Frequency: GPS L1GLONASS L1BDS B1GALILEO ESBAS L1QZSS L1 Input Voltage: 5V Antenna: Ceramic Antenna Channel: 72 Battery: Built-in Compass: QMC5883 Baud Rate: 115200bps Protocol: Dual NMEA/UBLOX Output Frequency: 1Hz-10Hz,10Hz default Speed Accuracy: 0.05m/s Horizontal Positioning Accuracy 2D ACC1.5m(outdoor) Receiver Sensitivity: Trace -166dBm; Capture -160dBm Dynamic Characteristics: Height 50000m; Speed 500m/s; Acceleration 4G Operating Temperature: -40C-+85C Storage temperature: -40C-+105C Weight: 12g Size: 25 x 25 x 8mm Includes Foxeer GPS M10Q-250 GPS & Compass (10th Gen)

Read more less

A compact GPS Module from HGLRC. When you get this GPS, expect extremely fast positioning with a stable signal. All on a small form factor, you'll get accurate positioning with this new 10th Gen GPS running off the Ublox protocol.  Check out our GPS selection and all our HGLRC products! Specifications  Chip: M10 (tenth generation chip) Antenna: ceramic antenna Frequency: GPS/QZSS L1C/A, SBAS EGNOS, GAGAN, MSAS and WAAS GLONASS L1OF, BDS B1I, Galileo E1B/C Receive channel: 72ch Baud rate: 115200bps. Output protocol: UBLOX Output frequency: 10Hz Power input: 3.3-5V Size: 21x21x8.02mm Weight: 7.73g Includes 1x HGLRC M100-5883 Micro GPS w/ Compass (10th Gen) Wiring Diagram and Betaflight

Read more less

The HGLRC M100_MINI GPS. Coming in with the new 10th generation UBLOX chip design, for fast and accurate positioning. With its small size of 15x15mm, this Mini GPS is compatible for your 2 to 7 inch long range quads. The ceramic antenna and externally expanded PCB design allow M100 MINI GPS to receive satellite signals more effectively. From the laboratory from HGLRC, their team has design the GPS to take to less than 1 minute for it to reach the 8 satellites required for take-off. At the same time, it supports receiving GPS, Galileo, and BDS three satellite signals, allowing you to locate in any area quickly. The HGLRC designers of this mini GPS harbors consideration for ease of use. With the onboard LED indicators, including the power indicator and positioning PPS indicator, so that you can know the working status of GPS well. Check out our GPS selection and all our HGLRC products!   Features Using the new 10th generation UBLOX chip design, fast and accurate positioning. New protection circuit for the signal IOs Selected ceramic antenna and externally expanded PCB design to effectively receive satellite signals Support GPS, Galileo, BDS three-mode positioning, and fast positioning in any area Compatible power supply, support 3.3V-5V DC power input Using UBLOX output protocol and 10Hz output frequency Specifications Chip: M10(10th Generation Chip) Power Supply: 5V Antenna: Ceramic Antenna Receiving Format:  GPS L1, GLONASS L1, BDS B1, GALILEO E1, SBAS L1, OZSS L1 Receiving Channel: 72  Baud Rate: 115200bps Output Protocol: UBLOX Output Frequency: 1Hz-10Hz,Default 10Hz Speed Precision: 0.05 m/s  Level Positioning Precision: 2D ACC2.0m(Outdoor) Receiving Sensitivity: Trace -166dBm Capture-160dBm Dynamic Characteristics: Max Height:50000m Max Speed: 500m/s Max Acceleration: 4G Working Temperature: -40℃-+85℃ Storage Temperature: -40℃-+105℃ Size: 18.5mm x 18.5mm x 7.1mm Weight: 2.6g Includes 1x HGRLC M100 Mini GPS Module Wiring Diagram and Betaflight setup    

Read more less

Compact GPS Module from HGLRC. Check out our GPS selection and all our HGLRC products! Specifications Chip: M8030 Power Supply: 5V Antenna: Ceramic Antenna Receiving Format: GPS,GLONASS,GALILEO,QZSS,SBAS,BDS Receiving Channel: 72 Searching Channel Support Rate: 115200dps Output Protocol: UBLOX Output Frequency: 1Hz-10Hz,Default 10Hz Speed Precison: 0.05 m/s  Level Positioning Precison: 2D Acc1.5m(ln Open Sky) Receiving Sensitivity: Trace -167dBm Capture-160dBm Dynamic Characteristics: Max Height:50000m Max Speed: 500m/s Max Acceleration: 4G Working Temperature: -40℃-+85℃ Storage Temperature: -40℃-+105℃ Size: 18.5mm x 18.5mm x 7.1mm Weight: 9.4g Includes 1x HGRLC M80 GPS Module

Read more less

Compact GPS Module from HGLRC. The HGLRC M80 PRO GPS Module comes with a QMC5883 chip to help identify the location of your drone quickly. Receives a stronger antenna signal to make it easier to be found by satellites. No soldering needed just plug directly and use.  The HGLRC M80 PRO GPS Module is ideal for FPV racing drones!  Check out our GPS selection and all our HGLRC products! Specifications Item: HGLRC M80PRO GPS Chip: M8030 Power Supply: 5V Antenna: Ceramic Antenna Receiving Format: GPS,GLONASS,GALILEO,QZSS,SBAS,BDS Receiving Channel: 72 Searching Channel Compass: QMC5883 Support Rate: 115200dps Output Protocol: UBLOX Output Frequency: 1Hz-10Hz,Default 10Hz Speed Precison: 0.05 m/s Level Positioning Precison: 2D ACC1.5m(ln Open Sky) Receiving Sensitivity: Trace -162dBm Capture: -160dBm Dynamic Characteristics: Max Height:50000m Max Speed: 500m/s Max Acceleration: 4G Working Temperature: -40℃-+85℃ Storage Temperature: -40℃-+105℃ Size: 25mm x 25mm x 8.3mm Weight: 12.5g Includes 1x HGRLC M80 Pro GPS Module

Read more less

Small and precise, the Holybro M10 Micro GPS with IST8310 Compass provides fast and accurate positioning with its Ublox 10th Gen GNSS. Get the most accurate navigation, and enjoy precise tracking during your travels. Check out our other GPS options and the rest of our HolyBro selection! Features Newest Ublox 10th Gen GNSS Fast & Accurate Positioning IST8310 Compass Small Form Factor  Plug and Play Specifications GNSS Receiver: Ublox M10 Receiver Number of Concurrent GNSS: Up to 4 (BeiDou, Galileo, GLONASS, GPS, QZSS) Compass: IST8310 Frequency Bands: GPS L1, Galileo E1, GLONASS L1, BeiDou B1, SBAS L1, QZSS L1 Output Protocol: UBX (U-blox), NMEA Nav. Update Rate: Up to 25 Hz (single GNSS) and Up to 10 Hz (4 concurrent GNSS) GNSS Augmentation System (SBAS): WAAS, EGNOS, MSAS GNSS Augmentation System (QZSS): L1S (SLAS) Default Baud Rate: 38400 Input Voltage: 4.7-5.2V Accuracy: 1.5m Speed Accuracy: 0.05 m/s Port Type: JST-GH-6P Antenna: 25 x 25 x 4mm ceramic patch antenna Power consumption: Less than 200mA @ 5V Port Type: JST-GH-6P Operating Temperature:  -40~80C Dimension: 32 x 26 x 9mm Weight: 14g Other Notes: LNA MAX2659ELT+ RF Amplifier, Rechargeable Farah capacitance, Rechargeable Farah capacitance Includes 1x Holybro M10 Micro GPS w/ IST8310 Compass (10th Gen) Wiring Diagram

Read more less

Holybro M9N Micro GPS w/ IST8310 Compass is the perfect navigation solution for professionals looking for maximum precision. This 10th gen GNSS module is built on the reliable u-blox M9N chip for exceptional sensitivity and acquisition times. It supports concurrent reception of four GNSS systems which maximizes accuracy under difficult conditions.  Check out our other GPS options and the rest of our HolyBro selection! Features Ublox M9N GNSS Receiver Fast & Accurate Positioning IST8310 Compass Small Form Factor Maximum position availability with concurrent reception of 4 GNSS Ultra-robust GNSS positioning Excellent RF interference mitigation Specifications GNSS Receiver: Ublox M9N Receiver Number of Concurrent GNSS: Up to 4 (BeiDou, Galileo, GLONASS, GPS, QZSS) Compass: IST8310 Frequency Bands: GPS L1, Galileo E1, GLONASS L1, BeiDou B1, SBAS L1, QZSS L1 Output Protocol: UBX (U-blox), NMEA Nav. Update Rate: Up to 25 Hz  GNSS Augmentation System (SBAS): WAAS, EGNOS, MSAS GNSS Augmentation System (QZSS): L1S (SLAS) Default Baud Rate: 38400 Input Voltage: 4.7-5.2V Accuracy: 1.5m Speed Accuracy: 0.05 m/s Port Type: JST-GH-6P Antenna: 25 x 25 x 4mm ceramic patch antenna Power consumption: Less than 200mA @ 5V Port Type: JST-GH-6P Operating Temperature: -40~80C Dimension: 32 x 26 x 9mm Weight: 14g Other Notes: LNA MAX2659ELT+ RF Amplifier, Rechargeable Farah capacitance, Rechargeable Farah capacitance Includes 1x Holybro M9N Micro GPS w/ IST8310 Compass (10th gen) Wiring Diagram 

Read more less

The iFlight BLITZ M10 GPS w/ Compass provides reliable positional and directional data for your quad. Its advanced compass and GPS module allow for precise coordinates and real-time flight information for optimal navigation. This high-performance unit helps ensure safe and accurate flight paths for your craft. Always keep a quad when you add a GPS! Check out our other GPS modules, as well as the rest of our iFlight Products Features Using the latest UBLOX M10 chip, lower power consumption, faster satellite search speed. Built-in high precision compass QMC5883L. Built-in Faraday capacitor, with 1-10Hz positioning update rate, which makes GPS have faster startup speed and satellite receiving speed. 18x18mm ceramic antenna provides the best balance and performance for current GPS modules, low power consumption, strong signal and light weight. On-board LNA low noise amplifier and RF filter provide excellent working environment for GPS module. Up to 10HZ refresh rate. Built-in Flash, users can set GPS parameters by themselves using U-center or other software, configuration modification will be stored to Flash, no loss of parameters after power failure. Pin Definitions  VCC: system main power supply, supply voltage is 5V, current is about 40mA when working GND: Ground RXD: data input TXD: Data output SDA: Serial Data - I2C Master/Slave Data DCL: Serial Clock - I2C Master/Slave Clock Light Indicator Blue light, TX light, the blue light blinks on power up, indicating that there is data output. Red light, PPS light, not positioned red light is not lit, 3D positioning, the red light began to flash Specifications  Compass module: QMC5883L Baud Rate: 4800bps-115200bps (Default - 115200bps) Sensitivity: Tracking: -167dBm Cold start: 26s Hot start: 1s Maximum height: 50000m Maximum speed: 500 m/s Speed accuracy: 0.05 m/s Maximum acceleration: ≦ 4G Refresh Rate: 10 Hz GPS patch antenna size: 18x18 mm Total dimensions: 20 x 21 x 6.5 mm Weight: 5.2 g（±0.5g） Input Voltage: 3.3-5.5 V, current 40mA GPS pin definition: RX/TX UART Compass pin definition: SDA/SLA Includes 1x iFlight BLITZ M10 GPS & Compass (10th Gen) 1x Cable Set

Read more less

The MATEKSYS M10Q-5883 supports GNSS (GPS, GLONASS, Galileo, and BeiDou) and thus offers excellent RF sensitivity. The SAM-M10Q uses a multi-constellation GNSS module powered by u-blox SAM-M10Q-00B. The SAM-M10Q features the u-blox M10 standard precision GNSS platform and provides exceptional sensitivity and acquisition time for all L1 GNSS signals. This feature will help you pick up the best signals. But also enhance the dynamic position accuracy with small antennas or in non-line-of-sight scenarios. The high number of visible satellites enables the receiver to select the best signals. Hence this maximizes the position availability, in particular under challenging conditions such as in deep urban canyons. The high-gain 15x15mm2 patch antenna provides the best balance between performance and small size. The omnidirectional antenna radiation pattern increases flexibility for device installation. Check out all our GPS modules, and our full line of Matek products! Features M10-5883 uses multi-constellation GNSS powered by u-blox SAM-M10Q-00B Ultra-low-power GNSS antenna module for easiest integration Simple design-in with no RF expertise required Less than 38 mW power consumption without compromising GNSS performance Maximum position availability with 4 concurrent GNSS reception Advanced spoofing and jamming detection Pin-compatible with previous SAM-M8Q Specifications GNSS  u-blox SAM-M10Q-00B (GPS, GLONASS, Galileo, and BeiDou) Magnetic Compass QMC5883L Patch antenna 15x15x4mm Input voltage range: 4~9V (5V pad/pin) Power consumption: 13mA UART baudrate: 9600 default Operating Temperatures: -20~80 °C UART(TX, RX) interface for GNSS SAM-M10Q-00B I2C(DA, CL) interface for Compass QMC5883L JST-GH-4P connector (SM04B-GHS-TB). 1.27mm pitch GNSS PPS LED, Green. (Solid ON after powering on, blinking(1Hz) when GNSS get 3D fix)  Protocol: UBX(u-blox) 5Hz@GPS+GAL+BDS B1C+GLO or NMEA 1Hz 20mmx20mmx12.4mm 8g Wiring and Settings M10Q-5883 5V to Flight controller 4~9V M10Q-5883 RX to Flight controller UART_TX M10Q-5883 TX to Flight controller UART_RX M10Q-5883 CL to Flight controller I2C_SCL M10Q-5883 DA to Flight controller I2C_SDA M10Q-5883 G to Flight controller GND Tips INAV 5.0.0, Betaflight 4.3.0, ArduPilot 4.3 or newer is required. UBlox NEO-M9N, MAX-M10S, SAM-M10Q series all don’t have dataflash built in. once GNSS is powered off and the supercapacitor run out. the settings will back to default. UBX protocol is bidirectional. Flight controller firmware can change settings on GPS via UBX protocol. You don’t need to set GNSS module Baud and Frequency in u-center. The default configuration on SAM-M10Q-00B with ublox FW 5.1 is concurrent reception of GPS, Galileo, GLONASS, and BeiDou B1C with QZSS and SBAS enabled. Start with u-blox GNSS FW3.01, timepulse is aligned with UTC time and that time is set valid only after leap second is downloaded. That could take up to 12.5 min. Probably PPS LED will not blink immediately after GPS has 3D fixed. The SAM-M10Q provides the ability to reset the receiver. Bridging “RST” pad to Ground for at least 100 ms will trigger a cold start. RESET will delete all information and trigger a cold start. It should only be used as a recovery option. If you are sure wiring and setup are all right. but flight controller can’t detect the GNSS module(grey GPS icon), try doing reset. The scratches on ceramic antenna are the result of tuning the antenna. Troubleshoot GPS related issues: http://www.mateksys.com/?p=5712#tab-id-6 u-center Windows Important Notes Compass Alignment(flat mounting): Tilting the magnetometer is strongly discouraged ! INAV/BetaFLight: compass Arrow forward, set CW 270° Flip when flight controller arrow is facing forward. INAV/BetaFLight: compass Arrow backward, set CW 90° Flip when flight controller arrow is facing forward. Ardupilot/Mission Planner: Rotation None. Make sure to have compass/magnetometer 10cm away from power lines/ESC/motors/iron based material Includes 1x Matek M10Q-5883 GNSS & Compass

Read more less

The Matek SAM-M10Q-5883 GNSS is a cutting-edge multi-constellation GNSS module featuring the advanced u-blox SAM-M10Q platform. It offers exceptional sensitivity and acquisition time for all L1 GNSS signals and can receive concurrent signals from four GNSS, including GPS, GLONASS, Galileo, and BeiDou. Its advanced Super-S technology further enhances RF sensitivity and dynamic position accuracy, even in challenging urban environments. Finally, with the high-gain 15 x 15 mm2 patch antenna provides the best balance between performance and small size. The omnidirectional antenna radiation pattern increases flexibility for device installation. Enjoy reliable readings for your drone navigation! Check out all our GPS modules, and our full line of Matek products! Features Simple design-in with no RF expertise required Less than 38 mW power consumption without compromising GNSS performance Maximum position availability with 4 concurrent GNSS reception Advanced spoofing and jamming detection Pin-compatible with previous SAM-M8Q Specifications GNSS u-blox SAM-M10Q-00B (GPS, GLONASS, Galileo and BeiDou) No Magnetic Compass built-in Patch antenna 15 x 15 x 4mm Input voltage range: 4~9V (5V pad/pin) Power consumption: 10mA UART baudrate: 9600 default Operating Temperatures: -20~80 °C UART(TX, RX) interface for GNSS SAM-M10Q-00B JST-GH-4P connector (SM04B-GHS-TB). 1.27mm pitch GNSS PPS LED, Green. (Solid ON after powering on, blinking(1Hz) when GNSS get 3D fix) Protocol: UBX(u-blox) 5Hz@GPS+GAL+BDS B1C+GLO or NMEA 1Hz 26mm x 16mm x 8mm 7.5g SAM-M10Q_step.zip Wiring and Settings AM-M10Q 5V to Flight controller 4~9V SAM-M10Q RX to Flight controller UART_TX SAM-M10Q TX to Flight controller UART_RX SAM-M10Q G to Flight controller GND Tips INAV 5.0.0, Betaflight 4.3.0, ArduPilot 4.3 or newer is required. UBlox NEO-M9N, MAX-M10S, SAM-M10Q series all don’t have dataflash built in. once GNSS is powered off and the supercapacitor run out. the settings will back to default. UBX protocol is bidirectional. Flight controller firmware can change settings on GPS via UBX protocol. You don’t need to set GNSS module Baud and Frequency in u-center. The default configuration on SAM-M10Q-00B with ublox FW 5.1 is concurrent reception of GPS, Galileo, GLONASS, and BeiDou B1C with QZSS and SBAS enabled. Start with u-blox GNSS FW3.01, timepulse is aligned with UTC time and that time is set valid only after leap second is downloaded. That could take up to 12.5 min. Probably PPS LED will not blink immediately after GPS has 3D fixed. The SAM-M10Q provides the ability to reset the receiver. Bridging “RST” pad to Ground for at least 100 ms will trigger a cold start. RESET will delete all information and trigger a cold start. It should only be used as a recovery option. If you are sure wiring and setup are all right. but flight controller can’t detect the GNSS module(grey GPS icon), try doing reset. The scratches on ceramic antenna are the result of tuning the antenna. Troubleshoot GPS related issues: http://www.mateksys.com/?p=5712#tab-id-6 u-center Windows Important Notes Compass Alignment(flat mounting): Tilting the magnetometer is strongly discouraged ! INAV/BetaFLight: compass Arrow forward, set CW 270° Flip when flight controller arrow is facing forward. INAV/BetaFLight: compass Arrow backward, set CW 90° Flip when flight controller arrow is facing forward. Ardupilot/Mission Planner: Rotation None. Make sure to have compass/magnetometer 10cm away from power lines/ESC/motors/iron based material Includes 1x Matek SAM-M10Q-5883 GNSS GPS Module 1x JST-GH-4P to JST-GH-4P 20cm silicon wire

Read more less

An unbelievably tiny GPS module, get even the smallest of quads linked up to satellites with this little guy! Check out our GPS selection! Specifications Input Power: 5V Antenna: Ceramic Antenna Receiving Format: GPS，GLONASS，BDS Support Rate: 9600dps Output Protocol: UBLOX Working Temperature: -40℃-+85℃ Storage Temperature: -40℃-+105℃ Size: 13mm x 13mm x 5.5mm Weight: 1.6g Includes 1x NamelessRC Tiny GPS Module Wiring Diagram

Read more less

Introducing the NewBeeDrone M10Q Micro GPS w/ Compass (10th Gen)'s advanced navigation capabilities, featuring wide-range precision GPS/compass technology. Improved accuracy, compact size, and lightweight design (17mmx12mmx5mm, 2.16g) make it ideal for navigating difficult terrain. Perfect for projects requiring space and weight conservation. The NewBeeDrone M10Q Micro GPS (10th Gen) is the ideal outdoor navigation tool. With its built-in compass, you'll be able to track your location while navigating remote areas with confidence accurately. Grab one of the newest, smallest, and most powerful FPV GPS on the market right now, brought to you by great people at NewBeeDrone.  Check out our other GPS options and all our NewBeeDrone products! Features 10th generation GPS Only weighing 2.16g Super tiny     Specifications Ceramic Antenna 2DB  Frequency: GPS L1, GLONASSL1, BDS B1, GALILEOE1, SBAS L1, QZSS L1 Compass: QMC5883 Baud Rate: 115200DPS Output Frequency: 1HZ-10HZ, Default 10HZ Power Supply: 5V  Speed Accuracy: 005M/S Weight: ~2.61g Includes 1x NewBeeDrone M10Q Micro GPS w/ Compass (10th Gen) 1x JST 0.8 6pin cable

Read more less

A reliable GPS with built in compass, all at a great price! Check out all our GPS modules! Features GPS Module, Dual Module Compass With electronic compass IC HMC5883L 1.25mm spacing between the 6pins patch seat Specifications Power Supply: DC Voltage 2.8V~6.0V Typical:3.3V or 5.0V Consumption: Capture 50mA@5V Receiving Format: GPS, GLONASS, Galileo, BeiDou, QZSS and SBAS Receiving Channel: 72 Searching Channel Receiving Sensitivity: Trace -167dBm Capture-148dBm Positioning Time: Cold Start: 26s Average Warm Start: 25s Average Hot Start: 3s Average Level Positioning Precision: 2m At Open Wind Output Frequency: 1Hz-10Hz,Default 1Hz Speed Precision: 0.1 m/s (Without Aid) Acceleration Precision: 0.1 m/s (Without Aid) Dynamic Characteristics: Max Height: 18000m Max Speed: 5153m/s Max Acceleration: 4G UART Interface: UART Port: TXDA and RXDA Support Rate: 4800bps to 115200bps,Default 38400dps Working Temperature:-40℃-+85℃ Storage Temperature:-40℃-+85℃ The Module’s Pins: SDA,GND,TX,RX,VCC,SCL Size: 28x28x10mm Weight: 10g Includes 1x BN-880 GPS Module  1x 15cm Cable 1x 3M double-sided tape square Setup Note: Can not use for flight control with SCM, but it is suitable for Open source flight controller.   GPS Program Set up documents and instructions: Please click here BN-880 GPS Configuration files Check out this great demonstration of the Rescue feature from our customer, Bill Adams:

Read more less

**3.3 VOLTS ONLY - DO NOT USE 5 VOLTS!** We recommend an input voltage of 3.3v. The result may not be immediate, but eventually supplying voltage out of component limits will kill it. Always verify prior to install that your system is giving the GPS the voltage you think it is via a multimeter. If your unit dies or fails to operate as you'd expect, this is likely the cause. The RDQ Micro M8N GLONASS GPS Module is 18x18mm in size, perfect for any Micro , or add Gps to your racer to add "lost tracker" . Only 6 Grams with cable. Note: Providing the GPS with over the spec'd voltage WILL destroy your unit. Check out our GPS selection! Joshua Bardwell says: "In the video above, I mistakenly power the GPS with 5v. The GPS needs 3.3v power, not 5v. Powering the GPS with 5v will destroy it." Specifications GPS: UBLOX NEO-M8N Micro TX LED: blue the data output, TX LED flashing PPS LED: red PPS LED not bright when GPS not fixed,flashing when fixed Current: Capture 50mA/5.0V VCC : DC Voltage 2.7V-3.6V Chip used is always the UBX-M8030 Acquisition Time: Cold Start : 26s Warm start : 25s Hot start : 1s UBLOX protocol /NMEA-0183 Receiving Format GPS,GLONASS,Galileo,BeiDou,QZSS and SBAS Frequency : GPS L1,GLONASS L1,BeiDou B1,SBAS L1,Galileo E1 Channels : 72 Searching Channel Includes 1x MINI GPS 1x Cable  1x Adhesive pad Setup More information about GPS Rescue Mode How to add a GPS in Betaflight 3.2 With the 3.2 release, Betaflight finally has decent GPS support. Here are some of the navigation features you can have on Betaflight OSD: Latitude Longitude Distance to home Speed Arrow pointing home Even better: if you have a telemetry-enabled receiver such as the X4R or XSR, you can send your location to the Taranis in real time. The Taranis will log your position, and keep the last known position available in case of a crash. This means it could save you time and maybe money in the long run. This unit comes preconfigured and ready to wire to a flight controller. However, if you want to mess with the settings you can configure it via a serial UART and u-center for Windows. This video is still mostly relevant if you need to do that. Wiring the gps unit is easy: just connect it to a free UART on your flight controller. Make sure that the wires are long enough that you can mount the gps on top of your quad.  If you are running a bottom mounted battery, the top of your HD camera mount is the best spot. I run a top mount, so I prefer heat shrinking the gps to a battery strap so I can have it on top of the battery. Once wired, configuring the gps is easy.  On the ports tab of Betaflight, select gps as a peripheral for the UART to which it’s wired. In this case I used UART 3. Then in the configuration tab: And if everything is wired correctly, when you restart betaflight you should see the GPS indicator light up at the top of the screen. Now there are two things you can do. If you have Betaflight OSD, you probably want to enable gps coordinates, distance to home and direction to home. I also like having the satellite count and gps speed, even though it’s not very accurate. My screen looks like this: The home arrow indicates that I’m flying mostly away from myself and 145 meters away. The GPS coordinates show that I am in… [left as an exercise for the reader]. The second thing you could do is set up your Taranis to log gps coordinates (assuming your receiver has telemetry, won’t work with an xm+). I won’t cover that now because this is enough for one post, I’ll save it for a future one. Happy flying and hope this saves you from losing a quad or two!  

Read more less

Stop wondering how fast your RC car can run and how high your RC Airplane or helicopter can fly. Now all these data come at your finger with the GPS SPEED METER by SkyRC. The popularity of GPS devices inspired SkyRC to design this gadget at about 41g. The Speed Meter is the result of SkyRC’s ongoing development efforts, boasting an ultra‐compact GPS module with hidden antenna design, the high‐sensitivity GPS receiver chip can do quick positioning, a robust controller IC to keep recording speed and altitude in real time. This gadget is ideal for RC racing/flying and casual biking, driving and long journey. User could easily view the screen while working out data such as speed, altitude total mileage/ kilometer, longitude/latitude. The gadget records the top speed and top altitude for instant recall after the running. It will help RC fans much to fine‐tune their RC gadgets to achieve better performance. Check out all our GPS modules while you're here! Features  Updated version allows for easy changing of MPH-KPH by a simple push of a button, no longer needs to be connected to a computer to make the change. Now supports GNSS (Global Navigation Satellite System) with GPS and GLONASS system that means there are more available satellites to lock onto to. This improves positional accuracy by tracking two satellite constellations instead of just GPS. 1M built-in memory, and adjustable frequency from 1Hz to 10Hz. Features an ultra-compact GPS module with hidden antenna design. The high-sensitivity GPS receiver quickly identifies position and a robust controller records speed and altitude in real time. Ideal for RC driving/flying and can be used for running, biking etc. Easy to view screen for quick readouts of speed, altitude, total distance, longitude/latitude. Records the top speed and top altitude for instant recall. Specifications Receiver: L1, 1575.42 MHZ Frequency: 1.023 MHZ Update frequency: 1 Hz. Antenna type: Built-in Satellite signal reception sensitivity: -159dBm Operating temperature: 0℃ to +50℃ Storage temperature: -10℃ to +60℃ Operating humidity: 5% to 90% Dimensions: 65.7x39.6x20.8mm Weight: 41g Manual Download Software Download Includes 1x SkyRC GPS Speed Meter

Read more less

Track how fast your RC vehicle at any time with this small device that pairs with your smartphone! The collected data gets transfered to your Phone with the next Blutooth connection.  GNSS Performance Analyzer (GSM020 allows you to measure and analyze many aspects of your RC car & airplane's performance using the latest GNSS engine (GPS, GLONASS) which gives you Acceleration, G-force, Speed, Time, Distance, High and Vertical Speed. Check out all our GPS modules while you're here! Features 3 different Modes for every opportunity (Drag Race, Track Race, Flying Mode) Built-in 1M flash (for up to 50 data records) Built-in rechargeable, LiPo bettery 200mAh (for more than 5 hours) In the App recorded data turns into useful analysis GPS Coordinator   Support both Metric and Imperial system of measurements Free App is compatible with iOS 9.0 and Android 5.0 (or above) Specifications 3 Modes : Drag Race/Track Race/Flying Mode Receiver: L1, 1575.42 MHz Update frequency: 10 Hz Antenna: built-in Sensitivity of satellite signal reception: -167dBm Operating temperature: 0 ° to + 40 ° Temperature at rest: -10 ° to + 70 ° Operating mode humidity: 5% to 90% Case Size: 40 x 39 x 16mm  Weight: 38g Includes 1x SkyRC GSM020 GNSS Performance Analyzer

Read more less

Most drone pilots have a problem when using the GPS on their drones. GPS modules are slow and get interference. A pilot must wait many minutes for a GPS fix. To do this, everything must be powered, which drains the battery and causes extra interference. It also has the potential risk to cause overheating issues to your quad components. In addition, when you finish a flight cycle and change the quad battery, the GPS needs to get a hot-start fix as the quad battery disconnected. ViFly wants to ease the pain of this process, and to this end designed and produced GPS-mate. The external power module just for your GPS. ViFly also embedded the VIFLY Finder 2 functions into this device, so it can work as a standard buzzer that controlled via your radio when the quad battery is connected, it also can work as a standalone buzzer that help you find the lost drone when the main battery has been ejected. Check out the rest of our gps gear, and other great Vifly products. Features Acts as a power source for your GPS unit Acts as a lost model buzzer Recharges during normal use On/Off switch for when you don't need it Specifications Weight: 3.5g Size: 26x20x8mm LiPo size: 3.7V 50mAH Buzzer Working Time: Up to 4 hours Input Voltage: 0.5-5.5V Charging Time: 1.5 Hours Output Current: Up to 80mA Buzzer Volume: up to 90dB Includes 1x ViFly GPS Mate 1x 4 Pin Cable 1x 5 Pin Cable 1x Manual Wiring Diagram

Read more less

Because the GPS chip is a new 10th generation chip, the flight controller needs to flash firmware 4.29 and above, and the firmware below 4.29 uses the NMEA protocol. Walksnail WS-M181 GPS made for the Walksnail Avatar VTX and Walksnail HD system. Check out our other GPS options, as well as the rest of our Walksnail HD products!   Features With its small size, light weight, fast positioning, and stable connection. It is suitable for FPV, RC airplane, quadcopter and others to enhance the users flight experience. Featuring the u-blox M10 platform UBX-M10050 GNSS chipset and BUILT-IN QMC5883 MAG, the module offers stronger performance and more accurate positioning. The ultra-thin ceramic antenna uses a special spray painting process to prevent oxidation and scratching, ensuring consistent positioning performance. The built-in battery can realize hot start and realize positioning quickly. It offers six positioning modes, providing more flexible combinations (default GPS + GLONASS + BDS multi-mode positioning).The measured maximum number of search stars can cover 32pcs. Specifications Chip: M10 (ten generation chip) Frequency: GPS L1,GLONASS L1,BDSB1,GALILEO E1,SBAS L1.QZSS L1 Power: 5V Size: 18mmx18mmx4.6mm Antenna: ceramic antenna (oil spraying process, prevent scratching and oxidation) Receiving channels: 72 search channels Compass： QMC5883 Baud rate: 115200dps Output protocol: NMEA UBLOX (dual protocol) Output frequency: 1Hz-10Hz, Default 10Hz Speed accuracy: 0.05m/s Horizontal positioning accuracy: 2D ACC1.5m(open air) Trace-162dBm Capture -160dBm Altitude: 50000m Speed: 500m/s Acceleration: 4G Operating temperature: -40℃-+85℃ Storage temperature: -40℃-+105℃ Includes 1x Walksnail WS-M181 GPS

Read more less