The FR16 Nano Baby V2 is a meticulously crafted microdrone with improved appearance, flight time, and power compared to its predecessor. Power has increased by 30%, with flexible flight, exceptional maneuverability, and higher speeds. A new canopy reinforces camera protection, while a new bottom plate adds sturdiness and crash resistance. The drone is equipped with a special gold-purple edition ROBO 1002 23,500KV motor and GOKU Versatile F411 VTX 1S AIO V2 with 250mW video transmitter. The Flywoo 1S Nano camera V3 delivers clearer and better image quality on this quad. Check out our other pre-built quads, as well as other great products from Flywoo! Features Redesigned canopy with enhanced aesthetics and reinforced camera protection. The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Equipped with ROBO 1002 23,500KV motor and 1609 4-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability. Ultra-light GOKU Versatile F411 1S VTX AIO V2 with upgraded circuit board stability and a 250mw video transmitter, enabling an extended flight range. A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector. Upgraded Flywoo 1S Nano camera V3 delivers clearer and better image quality. New battery compartment design allows for easy replacement of batteries of different models. Specification Motor:  ROBO 1002 23500KV Electronics:  GOKU Versatile F411 VTX 1S 5A AIO V2.0 w/250mW VTX Props:  1609 - 4 blade 40mm 1.5mm Shaft Camera:  Flywoo 1S Nano Camera V3 Receiver:  ExpressLRS 2.4GHz Weight:  26g Flight Time:  Explorer 1S 450mAh HV V2: 4m - Explorer 1s 750mAh HV V2: 6m (approximate) Speed:  80km/h (approximate) GOKU Versatile F411 VTX 1S 5A AIO V2.0 w/ 250mw VTX Flight Controller MCU: STM32F411CEU6  GYRO: ICM42688 UARTS: 1/2 Soft serial port：1 I2C: SCL/SDA BEC: 5V  Input Voltage: 1S (<4.35v) Firmware: FLYWOOF411_5IN1_AIO  Mounting:  25x25mm, M2 Onboard 4in1 ESC MCU: EFM8BB21 Power supply: 1S LiPo/LiPo HV Current: 5A  Firmware: BLHeli_S Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT 150/300/600 Onboard 5.8g VTX Output power: 25mw~250mw switchable Frequency: 40CH Frequency: 5.8GHz 5 bands 40 channels(include Race band) IRC ready Flywoo ROBO 1002 23500KV Fpv Motor: Configuration: 9N12P Stator Diameter: 10mm Stator Length: 2mm Shaft Diameter: 1.5mm Motor Dimension(Dia.xLen): Φ13.5x7.75mm Weight(g): 2.5(5cm wire) Idle current(5)@5V(A): 1.5 No.of Cells(Lipo): 1S Max Continuous Power(W)3S: 52 Internal Resistance: 75mΩ Max Current(3S): 14A Max Efficiency Current: (2-4A)>84% Flywoo 1S Nano Camera V3 Model: Flywoo 1S Nano Camera V3 Image Sensor: 1/3" CMOS Sensor Horizontal Resolution: 1200 TVL TV System: NTSC and PAL(switchable) MENU: Support IMAGE: 4:3 Synchronization: Internal Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio: >52dB (AGC OFF) Video Output: CVBS Lens: 1.8mm/F2.5 Min. illumination: 0.001Lux Auto Gain Control: YES BLC: YES WDR: Global WDR DNR: 3D DNR Dimensions: 14x14mm Wide Power Input: DC 3.7-18V Work Temperature: -20°C~+60C Work Humidity: 20%~80% Weight: 2.1g Includes 1x Flywoo BNF Firefly FR16 Nano Baby Analog V2.0 1.6" 1S Micro Quad - ELRS 2.4 GHz 4x 1609 - 4 40mm 1.5mm shaft 2x TPU Battery Mount 1x Hardware Screw Set 4x Prop guards

Read more less

Please note that this version is a kit and does NOT come with an O3 air unit, O3 camera and SanDisk Card. The CineRace is a double duct design, not a simple guard anymore. It can fly as flexibly as a racing drone, and as stable as Cinewhoop. All in all, this is a  drone that can not only race but also capture stable videos and at the same time achieve a super long flight time! A specially designed GM10 Nano V3 GPS module is tailored to fit the CineRace20, providing minimal weight but the ability to search up to 30 satellites. You will see on the front of the quad Flywoo engineer the use of the soft TPU material to mount the camera to prevent the jello effect, by reducing the over all vibrations in the quad. Come see our  Cinewhoop Collection and other great products from Flywoo! We also carry a version with the O3 Air Unit already installed here. Features Almost all parts are injection molded for a more sturdy and durable quad. Very easy to disassemble, only fixed by two aluminum columns Customizable with LEDs GPS up to 30 satellites Innovative duct design Sub250 (even with battery) Specifications Input Voltage: 4S Model: CineRace20 HD DJI O3 2inch (without Air Unit) Brand: FLYWOO Frame: CineRace20 O3 (Different fromCineRace20 V1.2\V2 frame ) Charge connector: XT30 Motor: NIN V2 1203PRO 4850Kv Propeller: D51-5 51mm  Buzzer : 5PCS Active Alarm Buzzer GPS: GOKU GM10 Nano V3 GPS Weight: 139g (without battery) Betaflight Firmware target: FLWO/FLYWOOF405S_AIO(SMT32F405) Recommended Battery:Explorer 450mah 4S ( flight time  5mins ) Explorer 750mah 4S ( flight time  6mins )  GOKU GN F405S 20A AIO Input Voltage: 2-6S Lipo MCU: STM32F405 BGA IMU: ICM42688 OSD: BetaFlight OSD  Blackbox: 16Mb Flash Baro: BMP280 BEC: 5V 6 hardware UARTS (UART1,2,3,4,5,6) Onboard LED：4x WS2812 Support BLHELI_S Support PWM, Oneshot125, Oneshot42, Multishot, Dshot150, Dshot300, Dshot600 FPV System Add your own O3 Air Unit Includes 1 x Flywoo CineRace20 HD V2 Neon LED 4S Cinewhoop (without O3 Unit) - PNP 8 x D51-5 props 2 x Battery strap  9x150mm \ 9x200mm 1 x Set of screws 1 x 90° USB Type-C 

Read more less

The FR16 Nano Baby V2 is an advanced microdrone with improved flight time, power, and appearance over its predecessor. It's 30% more powerful despite being heavier, with flexible flight, great maneuverability, and higher speeds. A newly designed canopy and plate provide crash resistance, and it's equipped with a ROBO 1002 23500KV motor. Plus, the GOKU Versatile F411 ELRS 1S AIO V2 + ELRS 2.4G receiver ensures a lightweight, top-performing design. This version utilizes the elite capabilities of the Walksnail HD digital VTX system.  The Walksnail Avatar HD Mini 1S Lite is a lightweight VTX designed for 1S whoop drones, featuring H.265 high-efficiency video coding technology, 1080P/60FPS image recording with 22ms ultra-low latency, and built-in 8 GB storage for interference-free HD video recording and USB exporting. Check out our other pre-built quads, as well as other great products from Flywoo! Features Redesigned canopy with enhanced aesthetics and reinforced camera protection. The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Equipped with ROBO 1002 23,500KV motor and 1609 4-bladed 40mm propellers, delivers a 30% increase in power, flexible flight, and impressive speeds perfect for racing competitions. The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance.  A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector. New battery compartment design allows for easy replacement of batteries of different models. Specification Motor:  ROBO 1002 23500KV Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0 Props:  1609 - 4 blade 40mm 1.5mm Shaft HD Digital VTX System:  Walksnail Avatar HD Mini 1S Lite Receiver:  ExpressLRS 2.4GHz Weight:  33g Flight Time:  Explorer 1S 450mAh HV V2: 4m - Explorer 1S 750mAh HV V2: 6m (approximate) Speed:  70km/h (approximate) GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller MCU: STM32F411CEU6  GYRO: ICM42688 UARTS: 1/2 Soft serial port: 1 I2C: SCL/SDA BEC: 5V  Input Voltage: 1S (<4.35v) Firmware: FLYWOOF411_5IN1_AIO  Mounting:  25x25mm, M2 Onboard 4in1 ESC MCU: EFM8BB21 Power supply: 1S LiPo/LiPo HVCurrent: 5A  Firmware: BLHeli_S Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT 150/300/600 ELRS 2.4G RX (UART2) Flywoo ROBO 1002 23500KV Fpv Motor: Configuration: 9N12P Stator Diameter: 10mm Stator Length: 2mm Shaft Diameter: 1.5mm Motor Dimension(Dia.xLen): Φ13.5x7.75mm Weight(g): 2.5(5cm wire) Idle current(5)@5V(A): 1.5 No.of Cells(Lipo): 1S Max Continuous Power(W)3S: 52 Internal Resistance: 75mΩ Max Current(3S): 14A Max Efficiency Current: (2-4A)>84% Walksnail Avatar HD Mini 1S Lite Model: Avatar mini 1s module Communication Frequency: 5.725-5.850GHz Transmitter Power (EIRP): FCC:<25.5dBm;CE:<14dBm;SRRC:<20dBm; MIC:<25dBm I/O Interface: JST1.0x6(Power in)JST1.0x4(USB) Mounting Holes: 25.5x25.5mm Dimensions: 30x30x6.5mm Storage: 8G Recording: 1080p/720p Weight: 5.1g Operating Temperature: -20-40℃ Channels: 8 Wide Power Input: 3.1V-5V Supported FC System: Betaflight OSD: Canvas mode Bitrate: 25mbps, 50mbps Latency Average delay: 22ms Antenna: IPEX Avatar lite camera Model: Avatar lite camera Image Sensor: 1/2.7”1nch Resolution: 1080P/60fps,720P/120fps,720P/60fps Ratio: 16/9 4/3 Lens:2.1mm FOV: 170° Aperture: F2.0 Shutter Rolling: Rolling shutter Min.Illumination: 0.001Lux Weight: 1.8g Dimensions: 14x14x16mm  Includes 1x Flywoo BNF Firefly FR16 Nano Baby HD V2.0 1S 1.6" Micro Quad w/ Avatar Nano Cam - ELRS 2.4 GHz 4x 1609 - 4 40mm 1.5mm shaft 2x TPU Battery Mount 1x Hardware Screw Set 4x Prop guards

Read more less

Flywoo's Firefly Hex Nano V1.2 is the smallest hexacopter ever designed by Flywoo, weighing in at 74g. It powerfully and stably carries Insta 360go and SMO 4K cameras. The Firefly hex nano is small, flexible, stable, and is full of power and offers unmatched control. Check out our other pre-built quads, as well as other great products from Flywoo! Feature Hexacopter HD system Naked Vista Weighing only 74 grams Built in SMO Power Cable Prebuilt and tested Specifications Weight: 74g Wheelbase: 80mm FC & ESC:【No.C203】GOKU HEX F4 16x16 STACK - ( FC+13A ESC ) ( MPU6000) Frame: Firefly Baby Quad Frame (HD Verison) Motors: Nin V2 1203Pro 5500Kv Props: Gemfan 1636 40mm-4 V2.0 HD digital camera & VTX: Naked RunCam Link & RunCam Wasp Antenna: Atomic 5.8GHz Antenna Length 30mm (LHCP) Battery (Recommended): 4S 450mAh / 4S 300mAh battery (Not including) GOKU HEX GN405 Nano16X16 FC  MCU: STM32F405 BGA IMU: ICM42688P Barometer: DPS310 input voltage： 2-6S Onboard LED：WS2812x4 6 hardware UARTS (UART1,2,3,4,5,6) Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported. Onboard 16Mbytes for Blackbox logging 5V Power Out: 2.0A max 3.3V Power Out: 0.5A max Dimensions: 22x22mm Mounting Holes: 16x16mm Weight: 2.3g Firmware : FLYWOOF405NANO BS13A BLheli_S 2-4S 4in1 lBS20/35A BLheli_S 2-6S 4in1 Weight: 2.5g Mounting Hole: 16x16mm (M3) Support Oneshot, Multishot, DShot150/300/600 Nin V2 Motor Stator Size: 1203 Motor Bolt Pattern: 9x9mm KV: 5500 Wasp Nano HD Camera Dimensions: L18mmxW14mmxH18mm LENS: FOV D:160° H:127° V:92° Resolution: 720P@120fps(4:3) Net Weight: 6g(With Cable) Shutter: Rolling Shutter Coaxial Cable: 80 mm Image Sensor: 1/3" Naked Link Air Unit Input Voltage: 7.4-26.4V@ 4-9W Operating Frequency: 5.725-5.850 GHz Transmitter Power: (EIRP) FCC/SRRC: <30 dBm; CE: <14 dBm Min. Latency (end-to-end): 1280 x 720 60fps: 32 ms Max. Transmission Distance: FCC/SRRC: 4 km; CE: 0.7 km; I/O Interface: Type-C, IPEX, 3-in-1 port, Supported Flight Control System: BetaFlight Operating Temperature Range: 0° to 40° C (32° to 104° F) Includes 1x Flywoo BNF Firefly Hex Nano V1.2 1.6" HD 4S Micro Quad w/ Naked RunCam Link & RunCam Wasp - Choose Receiver 1x Accessories (props, prop guard, RunCam link shell, battery straps, hardware, ect)

Read more less