The Nazgul5 HD V3 is loaded with lots of power and performance; it comes with the XING-E Pro 2207 6S motors, BLITZ F722 FC, and BLITZ E45S 45A 4-in-1 ESC, which makes this quad a must-have! Now with the DJI O3 Air Unit! The Nazgul V3 is one of the best freestyle frames for its value.  The Nazgul5 V3 HD has been pre-tuned and set up with everything you need, all you need to do is bind-and-fly. The Nazgul5 V3 is a 5" freestyle frame made of super stiff carbon for minimal resonance. Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products! Features XING-E Pro 2207 motors and NAZGUL F5 props 5" version also fits 5.1" style propellers Fits both 30.5x30.5 and 20x20 stacks 5mm arm design for more durability Popular True-X configuration LED illuminated logo TPU crash-guards Easy-Swap arms Specifications Operating Temperature Range：-10° to 40° C (14° to 104° F) Max Wind Speed Resistance: 130 Km/H (Level 4) Receiver: DJI BNF, ELRS Dimensions (L×W×H): 180×180×80 mm Max Speed: 130 Km/h (Manual Mode) Video Transmission: DJI O3 Air Unit Maximum Takeoff Altitude: 5000 m Product Name：Nazgul5 V3 6S HD ESC: BLITZ E45S 45A 4-IN-1 ESC Max Hover Time: Approx. 8 mins Motor: XING-E Pro 2207 motors Takeoff Weight: Approx. 620 g Prop: Nazgul 5 inch propellers Diagonal Distance: 245mm Frame: 255mm wheelbase Max Flight Distance: 5 km Antennas: 2 Antenna FC: BLITZ F722 GNSS: N/A Video Transmission  Product Name: DJI O3 Air Unit Weight: Approx. 36.4 grams（headband included） Dimensions (L×W×H): L32.5x W30.5xH 14.5mm Communication Bandwidth： Max 40 MHz FOV (single screen): 155° Communication Frequency: 2.400-2.4835 GHz；5.725-5.850 GHz End-to-End Latency With DJI FPV Goggles V2: 810p/120fps Video Transmission Quality: The latency is lower than 28 ms. 810p/60fps Video Transmission Quality: The latency is lower than 40 ms. With DJI Goggles 2: 1080p/100fps Video Transmission Quality: The latency is as low as 30 ms. 1080p/60fps Video Transmission Quality: The latency is as low as 40 ms. Max Video Transmission Bitrate: 50 Mbps Max Video Transmission Range：10 km (FCC), 2 km (CE), 6 km (SRRC) Operating Temperature Range: -10º to 40º C (14° to 104° F) Power Input: 7.4-26.4 V Audio Transmission: N/A Includes 1x iFlight BNF Nazgul5 V3 HD  6S 5" Freestyle Quad w/ DJI O3 Air Unit & Micro Cam - Choose Receiver 2x Nazgul 5 inch propellers (Set of 4) 2x Battery Pad 2x Antenna

Read more less

Pre-Orders shipping ASAP! For those just starting out with FPV drones and on a budget, BabyApe Ⅱ is a great choice. It builds on the design of the first generation of BabyApe, but with a higher spec and only a small price increase, making it the perfect starter drone for the cost-conscious flyer. DarwinFPV has always been committed to designing cost-effective FPV drone. They have accepted feedback from pilots, solved the problems that pilots are most concerned about, and brought better products to everyone who uses them. Adhering to these beliefs, DarwinFPV brings BabyApe Ⅱ. BabyApe Ⅱ is a 3.5-inch small freestyle FPV drone with a take-off weight of less than 250g that fulfills most countries' regulations. The BabyApe Ⅱ has a more powerful configuration, adopts a more reliable manufacturing process and a new power system, and has a higher level of performance, durability, and power. The flight time can reach 13 minutes, the flight distance is 1.5 kilometers, and the maximum speed is up to 92km/h.  The 4S version comes with powerful 1504-3600Kv motors, and choose between PNP (No RX)  or ELRS 2.4GHz for your receiver! Check out our other pre-built quads, as well as the rest of our DarwinFPV selection!  Features Compared with similar products of other brands, BabyApe Ⅱ only sells for $139.99, which once again perfectly reflects the super high-cost performance； It comes with 1504 motors and 3.5-inch propellers, the power is stronger and the response speed is faster; The camera and stack are protected by glue potting, which effectively prevents the risk of damage due to contact with metal particles, fine sand, gravel, weeds or dew, and the entire electronic system is more reliable and durable; The addition of a buzzer and extra LED lights is extremely beneficial for beginners, who frequently confront circumstances such as over-discharge the battery and locating drones due to mistakes that lead the drone to crash; The independent action camera base can be used with naked GoPro, thumb camera, etc. to record amazing images during flight at 4K/60 frames.   Specifications Brand: DarwinFPV Model: BabyApe Ⅱ 4S Frame: Wide X Wheelbase: 156mm Size: 126mmx150mmx50mm Flight Control: F411 MPU6500 AT7456E Firmware：DARWINF411 Firmware: BETAFPV_Nano_2400_RX The receiver's factory firmware is ELRS_V3.2.0 Reserved port: 1x SBUS(RX1 reverse)、2x Uarts(1,2)、2x Softserial, 1x I2C、1x RGB、1x Buzzer、1x USER(A15)、1x USB ESC: Bluejay 48KHz 3-6S 30A Motor:  4S version：1504-3600KV Propeller: HQProp T3.5x2x3GR-PC Weight: 135.4 g (analog version) Receiver: ELRS 2.4GHz Darwin FPV "Cement" Ultra Durable FPV Drone Camera Sensor type：1/3" CMOS Sensor Image：16:9 TV System: NTSC Horizontal Resolution：1200TVL Lens：2.1mm 160° Electronic Shutter: 1/50~1/100000 sec Video Output: CVBS Min. Illumination：0.001Lux wb: automatic DNR: 3D DNR WDR: 100db Input voltage: DC 3.7-24V Working current：80mA@DC12V/170mA@DC5V IP: IP67 Size：19x19mm Weight：7.9g DarwinFPV 25/200/400/600mW VTX Output Power: 25/200/400/600mW(adjustable) Frequency: 5.8Hz 40port Power Supply Voltage Range: 5V Weight: 3.5g Pitch: 28x15mm(length x width) Protocol: SmartAudio Indicator Light Description: Includes 1x DarwinFPV BNF Baby Ape V2 3.5" Analog Micro Quad - 4S - Choose Your Receiver 4x HQProp T3.5x2x3GR-PC 2x Battery cable strip ( 10x170mm) 2x EVA shock pad（thickness：10㎜） 1x Spare screws bag 1x Sticker 1x Manual

Read more less

The Babyhawk O3 picks up where the Babyhawk II HD equipped with the Caddx Vista left off. Customers have loved the Babyhawk II platform, and we have heard the calls for a variant equipped with ExpressLRS and the DJI O3 Air Unit. This new version of Babyhawk is stronger than the previous generation and boasts a DJI O3 Air Unit, the new Babyhawk O3 can truly become a long-flying video capture acro drone for general use and fun as well as content creation. No more need to carry a GoPro, a big complaint of the Babyhawk II. Customers can now capture high-quality 4K video all with the onboard O3. Check out all our pre-built quads, and all our EMAX gear! Features Improved video transmission with DJI O3 system  More durable frame redesigned for resilience. Sub 250 grams Specifications Wheelbase: 155mm Dry Weight: 154g Frame Material: Carbon Fiber Prop: Avan 3.5  Maximum size: 210mm Input Voltage: 2-4S Lipo Includes 1x EMAX BNF Babyhawk O3 w/ DJI O3 Air Unit - ELRS

Read more less

The FR16 Nano Baby V2 is a meticulously crafted microdrone with improved appearance, flight time, and power compared to its predecessor. Power has increased by 30%, with flexible flight, exceptional maneuverability, and higher speeds. A new canopy reinforces camera protection, while a new bottom plate adds sturdiness and crash resistance. The drone is equipped with a special gold-purple edition ROBO 1002 23,500KV motor and GOKU Versatile F411 VTX 1S AIO V2 with 250mW video transmitter. The Flywoo 1S Nano camera V3 delivers clearer and better image quality on this quad. Check out our other pre-built quads, as well as other great products from Flywoo! Features Redesigned canopy with enhanced aesthetics and reinforced camera protection. The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Equipped with ROBO 1002 23,500KV motor and 1609 4-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability. Ultra-light GOKU Versatile F411 1S VTX AIO V2 with upgraded circuit board stability and a 250mw video transmitter, enabling an extended flight range. A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector. Upgraded Flywoo 1S Nano camera V3 delivers clearer and better image quality. New battery compartment design allows for easy replacement of batteries of different models. Specification Motor:  ROBO 1002 23500KV Electronics:  GOKU Versatile F411 VTX 1S 5A AIO V2.0 w/250mW VTX Props:  1609 - 4 blade 40mm 1.5mm Shaft Camera:  Flywoo 1S Nano Camera V3 Receiver:  ExpressLRS 2.4GHz Weight:  26g Flight Time:  Explorer 1S 450mAh HV V2: 4m - Explorer 1s 750mAh HV V2: 6m (approximate) Speed:  80km/h (approximate) GOKU Versatile F411 VTX 1S 5A AIO V2.0 w/ 250mw VTX Flight Controller MCU: STM32F411CEU6  GYRO: ICM42688 UARTS: 1/2 Soft serial port：1 I2C: SCL/SDA BEC: 5V  Input Voltage: 1S (<4.35v) Firmware: FLYWOOF411_5IN1_AIO  Mounting:  25x25mm, M2 Onboard 4in1 ESC MCU: EFM8BB21 Power supply: 1S LiPo/LiPo HV Current: 5A  Firmware: BLHeli_S Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT 150/300/600 Onboard 5.8g VTX Output power: 25mw~250mw switchable Frequency: 40CH Frequency: 5.8GHz 5 bands 40 channels(include Race band) IRC ready Flywoo ROBO 1002 23500KV Fpv Motor: Configuration: 9N12P Stator Diameter: 10mm Stator Length: 2mm Shaft Diameter: 1.5mm Motor Dimension(Dia.xLen): Φ13.5x7.75mm Weight(g): 2.5(5cm wire) Idle current(5)@5V(A): 1.5 No.of Cells(Lipo): 1S Max Continuous Power(W)3S: 52 Internal Resistance: 75mΩ Max Current(3S): 14A Max Efficiency Current: (2-4A)>84% Flywoo 1S Nano Camera V3 Model: Flywoo 1S Nano Camera V3 Image Sensor: 1/3" CMOS Sensor Horizontal Resolution: 1200 TVL TV System: NTSC and PAL(switchable) MENU: Support IMAGE: 4:3 Synchronization: Internal Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio: >52dB (AGC OFF) Video Output: CVBS Lens: 1.8mm/F2.5 Min. illumination: 0.001Lux Auto Gain Control: YES BLC: YES WDR: Global WDR DNR: 3D DNR Dimensions: 14x14mm Wide Power Input: DC 3.7-18V Work Temperature: -20°C~+60C Work Humidity: 20%~80% Weight: 2.1g Includes 1x Flywoo BNF Firefly FR16 Nano Baby Analog V2.0 1.6" 1S Micro Quad - ELRS 2.4 GHz 4x 1609 - 4 40mm 1.5mm shaft 2x TPU Battery Mount 1x Hardware Screw Set 4x Prop guards

Read more less

All product containing lithium batteries must be shipped by a ground shipping method.Following the groundbreaking performance of the predecessor, comes the newly re-invented Tinyhawk II Freestyle, the perfect beginner outdoor FPV quad! Check out all our pre-built quads, and our selection of EMAX gear! Features Durable aerospace grade 3k woven carbon fiber BlHeli_S ESC F4 (MATEKF411RX Firmware) Flight Controller RunCam Nano 2 FPV camera More powerful VTX with 25/100/200mw power levels Smart Audio connected FRSKY D8 compatible Efficient Emax 1103 7000Kv brushless motors Avan Rush 2.5" props   Specifications Frame Wheelbase: 115mm Dry Weight: 49g All Up Weight: 79g with 2x 450mAh 1S battery Frame Material: Carbon Fiber Motors Stator Size: 1103 Kv: 7000kv Propeller Mount: T-mount, 1.5mm shaft Propeller: Avan Rush 2.5" All-In-One (AIO) Flight Controller Flight Controller: F4 (MATEKF411RX Firmware) ESC: 4-in-1 5A BlHeli_S Receiver: EMAX SPI Receiver (Compatible with FrSky D8 mode) Battery Connector: JST-PH2.0 Duo FPV System Ham radio license required for use in North America. VTX Power: 25/100/200mw Switchable (set to stay at 25mW until armed)* Channels: 37CH incl. Raceband Camera: RunCam Nano 2 1/3" 700TVL CMOS Smart Audio Connected Includes 1x Tinyhawk II Freestyle BNF 2x EMAX 450mAh 1S HV Battery 1x 1S USB LiPo Charger 1x Hardware Kit

Read more less

Introducing the smallest HD whoop with the DJI O3 currently on the market. This amazing 75mm quadcopter comes with the elite DJI O3 Air Unit and O3 Micro Cam, and the new BeeBrain BLV4 HD F7 AIO flight controller. Achieve sharper HD capture with amazing quality with O3 Air Unit. Boasting powerful 0804 12000kv dual ball bearings motors, despite its small size, this thing will rip!  Check out our other pre-built quads, as well as the rest of our NewBeeDrone selection. Explore and film spaces you never could before in HD! A must-have tool for professionals and hobbyists specializing in indoor space. The only HD Micro whoop board with F7 processor. Dual-bearing motors allow less friction in spinning while 3-blade Azi propellors were developed with engineering theory for optimal air-grab and stability. We master-tuned this drone to have the smoovest flight and absolutely no jello in any videos.  We found the best ratio between the size of drone and its weight distribution. Without DJI O3, the drone can fly up to 8 minutes. Up to 3 minutes with DJI O3 and battery. Choose between 3D printed battery mounts or strap.   We ensure that you get the best material and components  that are available so you can rely on the drone without troubleshooting or breaking. All parts are available separately as replacements. Additional flexibility with SLS Nylon prints allow cameras to be changed or updated if needed.  Assembly or tuning not required. Save time and energy so you can focus on your footage. Drone comes with built-in ExpressLRS and ready to pair. Built-in blackbox records data for tuning. Configure to DJI PNP on Betaflight if needed. Don't be afraid of messing up on customization. Reset to factory default (with our tunes and dump files) in one click if something is not right. Specifications  Drone Size: 75mm Flight Controller: BeeBrain BLV4 HD F7 Flight Controller ExpressLRS (ELRS) 2.4G Frame: Cockroach75 Brushless Frame Motors: Flow 0804 12000kv Double Ball Bearing Brushless Motor Propellesr: Azi (Tri-Blade) Micro Propellers 40mm - 1.0mm Shaft HD VTX & Camera: DJI O3 Air Unit Canopy: NewBeeDrone Acrobee75 HD O3 Canopy Total Weight without battery: 70.19g Total Weight with battery: 98.24g BeeBrain BLV4 HD F7 Flight Controller ELRS2.4G Specifications: MCU: STM32F745 ESC Firmware: S-H-40 - Bluejay, 0.19.2, 48kHz. ESC Specifications: 4 channel 12A ESC ESC Connector: JST-1.0 3Pin Weight: 6.6 grams (including antennas and battery connector) Size: Outer dimensions 29 x 29 x 7.6 mm Holes: 25.5 x 25.5 mm Battery input: 2S Connector: XT30 Internal Blackbox: 16MB Gyro: BMI270 UART1: SBUS on DJI Connector (RX only) UART2: TX & RX for internal ExpressLRS 3.0 receiver UART3: TX & RX for DJI MSP+Displayport Flight time with Tattu 450mAh 2S battery is 3:00min (at 7v)  Firmware:  BeeBrain BLV4 HD Betaflight 4.4.0 firmware with tune Includes 1x NewBeeDrone BNF AcroBee75 BLV4 2S HD 75mm w/ DJI O3 Air Unit & Micro Cam - ELRS 2.4GHz

Read more less

NewBeeDrone's latest whoop, the AcroBee BLV4 is perfect for flying indoors and outdoors. The technology and level of detail built into this whoop are astounding! With new "Smart Max" technology, uses the MCU to read the board temperature on the back of the VTX chips and uses PID control to control the output power for the VTX amplifier. If the temperature is low enough, the PID will adjust the output power higher, a maximum of 400Mw, and if the temperature rises, the output power of the VTX is lowered to avoid overheating.  With the VTX power, combined with ELRS, this whoop will fly far. Check out our other pre-built quads, as well as the rest of our NewBeeDrone selection. Features Classic Design with a newly refreshed appearance New Flow 0802 19000Kv Motors On-board temperature regulation prevents damage to boards. Built-in ELRS receiver Specifications Flight Controller: BeeBrain BLv4 ELRS MCU: STM32F411 VTX: Switchable output power from 5mw- 25mw(for Racing) - SmartMAX (SmartMax up to 400mw) with BeeTX 5.8Ghz Antenna ESC: 12A BLHeliS Pre-Flash with Bluejay 0.16 target: S-H-40 48kHz ESC Connector: JST-1.0 3Pin OSD: NBD7456 Graphical OSD compatible with Betaflight OSD Receiver: ELRS2.4 Diversity receiver (ESP32 compatible with wifi&bluetooth firmware update) 2.4G T-Antenna (Top) & normal 2.4G antenna (bottom) Flight Controller Weight: 6.5g (Include antennas and battery connector) Flight Controller Size: Outer dimensions: 29x29x7.6mm Flight Controller Holes: 25.5x25.5mm Battery input: 1-2S Uart2: Tx & Rx for ExpressLRS2.4G Receiver Uart1: Tx & Rx free Power Connector: NBD-PH2.0 connector Motors: Flow 0802 19000kv Frame: Cockroach65 Brushless Frame Clear Purple Camera Mount: Goober Canopy Clear Purple Propeller: Azi Tri-blade 31mm 1.0 Clear Purple Firmware: 1. BeeBrain blv4 ELRS3.0 receiver firmware 2. BeeBrain blv4 ELRS2.0 receiver firmware All firmware can be found on their Github Page Includes 1x NewBeeDrone BNF AcroBee65 BLV4 Brushless Whoop - ELRS 2.4GHz  

Read more less

All batteries must be shipped by a ground shipping method. Cetus X Brushless Quadcopter is a 2S power whoop drone and a primary choice for beginners who want to get advanced flight skills. It features a stronger propulsion system for a speedier and more violent flight, which is capable of performing diverse freestyle tricks. Equipped with M04 400mW VTX and C04 FPV camera that is optimized for longer radio and video transmission. Meanwhile, it supports the Betaflight configurator which is a popular application to configure RC aircraft. Check out our other RTF combos, all our pre-built quads and our BetaFPV selection! Features An excellent preference for beginners to get advanced level. Cetus X brushless Quadcopter is proud of its lightning speed with rapid startup due to its stronger propulsion system. Build-in ExpressLRS 2.4G receiver that is the most popular radio link, low latency, and far controlling range are possible. Pilots can not only enjoy the flight indoors but also explore the scenery outdoor. Featuring M04 400mW VTX, C04 FPV camera (based on Caddx Nano Ant Camera or Runcam Nano 4), and 2xBT2.0 450mAh 1S 30C battery for longer radio and video transmission and flight endurance, Cetus X brushless quadcopter allows beginners to gain more achievements in FPV flight. Classical white design inherited from Cetus Series and made of PA12 material, Cetus X frame has an excellent impact resistance in drop & impact. The 360° protection of the whoop frame ensures safe flights both indoors and outdoors. Meanwhile, the FPV camera supports 0°-40° adjustable degrees, which provides different views for pilots. Specifications Item: Cetus X Brushless Quadcopter Weight: 55g Wheelbase: 95mm FC: F4 1S 12A FC V2.2 (ELRS 2.4G) Motors: 1103 11000KV Motor Props: Gemfan 2020 4-Blades Props Camera: C04 FPV Camera (Caddx Nano Ant Camera/Runcam Nano 4) Camera Adjustable Angle: 0°-40° Receiver Protocol: ELRS 2.4G VTX: M04 25-400mW VTX Battery: 2*BT2.0 450mAh 1S 30C Battery Flight time: 5 mins Downloads FC Firmware and ESC download   Includes 1 x Cetus X Brushless Quadcopter 1 x BT2.0 Battery Charger and Voltage Tester 2 x BT2.0 450mAh 1S 30C Battery 1 x Phillips Screwdriver 1 x Prop Removal Tool 1 x Type-C Adapter 4 x Gemfan 2020 4-Blades Props  

Read more less

Pre-Orders shipping ASAP! For those just starting out with FPV drones and on a budget, BabyApe Ⅱ is a great choice. It builds on the design of the first generation of BabyApe, but with a higher spec and only a small price increase, making it the perfect starter drone for the cost-conscious flyer. DarwinFPV has always been committed to designing cost-effective FPV drone. They have accepted feedback from pilots, solved the problems that pilots are most concerned about, and brought better products to everyone who uses them. Adhering to these beliefs, DarwinFPV brings BabyApe Ⅱ. BabyApe Ⅱ is a 3.5-inch small freestyle FPV drone with a take-off weight of less than 250g that fulfills most countries' regulations. The BabyApe Ⅱ has a more powerful configuration, adopts a more reliable manufacturing process and a new power system, and has a higher level of performance, durability, and power. The flight time can reach 13 minutes, the flight distance is 1.5 kilometers, and the maximum speed is up to 92km/h.  The 6S version comes with powerful 1504-2300Kv motors, and choose between PNP (No RX)  or ELRS 2.4GHz for your receiver! Check out our other pre-built quads, as well as the rest of our DarwinFPV selection!  Features Compared with similar products of other brands, BabyApe Ⅱ only sells for $139.99, which once again perfectly reflects the super high cost performance； It comes with 1504 motors and 3.5-inch propellers, the power is stronger and the response speed is faster; The camera and stack are protected by glue potting, which effectively prevents the risk of damage due to contact with metal particles, fine sand, gravel, weeds or dew, and the entire electronic system is more reliable and durable; The addition of a buzzer and extra LED lights is extremely beneficial for beginners, who frequently confront circumstances such as over-discharge the battery and locating drones due to mistakes that lead the drone to crash; The independent action camera base can be used with naked gopro, thumb camera, etc. to record amazing images during flight at 4K/60 frames.   Specifications Brand: DarwinFPV Model: BabyApe Ⅱ 6S Frame: Wide X Wheelbase: 156mm Size: 126mmx150mmx50mm Flight Control: F411 MPU6500 AT7456E Firmware： DARWINF411 Firmware: BETAFPV_Nano_2400_RX The receiver's factory firmware is ELRS_V3.2.0 Reserved port: 1x SBUS(RX1 reverse)、2x Uarts(1,2)、2x Softserial, 1x I2C、1x RGB、1x Buzzer、1x USER(A15)、1x USB ESC: Bluejay 48KHz 3-6S 30A Motor： 6S version：1504-2300KV Propeller: HQProp T3.5x2x3GR-PC Weight: 135.4 g(analog version) Receiver: ELRS 2.4GHz Darwin FPV "Cement" Ultra Durable FPV Drone Camera Sensor type：1/3" CMOS Sensor Image：16:9 TV System: NTSC Horizontal Resolution：1200TVL Lens：2.1mm 160° Electronic Shutter: 1/50~1/100000 sec Video Output: CVBS Min. Illumination：0.001Lux wb: automatic DNR: 3D DNR WDR: 100db Input voltage: DC 3.7-24V Working current：80mA@DC12V/170mA@DC5V IP: IP67 Size：19x19mm Weight：7.9g DarwinFPV 25/200/400/600mW VTX Output Power: 25/200/400/600mW(adjustable) Frequency: 5.8Hz 40port Power Supply Voltage Range: 5V Weight: 3.5g Pitch: 28x15mm(length x width) Protocol: SmartAudio Indicator Light Description: Includes 1x DarwinFPV BNF Baby Ape V2 3.5" Analog Quad - 6S - Choose Your Receiver 4x HQProp T3.5x2x3GR-PC 2x Battery cable strip ( 10x170mm) 2x EVA shock pad（thickness：10㎜） 1x Spare screws bag 1x Sticker 1x Manual

Read more less

The props for this BNF press fit on and do not screw into the motor (much like many other Whoops & Toothpicks) The only difference between the Baby Ape and Baby Ape Pro versions is the camera. Darwin FPV is coming in hot with this affordable new 3" quad. Finding a good quad at a decent price is almost impossible these days but DarwinFPV has done it with this little ripper! Make sure to check out all of our BNF quads as well as the rest of our DarwinFPV selection! Specifications Motors Input Voltage: 1-3S Stator Size: 11x4mm KV: 4300 AIO MCU: STM32F411 Gyro: MPU6000 BEC: 5V/2A,3.3V Input voltage: 1-3S Lipo Support Receiver: PPM, Ibus, Sbus, Dsmx Black box: NO Barometer: NO Firmware: MATEKF411 Buzzer interface: YES Betaflight OSD: AT7456E Constant current: 15A Peak current: 17A MCU: EFM8BB21F16G(48MHz) Firmware: BLHeli_S Protocol: Dshot600 Mounting: 25.5X25.5 M2 VTX Input Voltage: 7V~24V RF Output Power: 0mW/25mW/100mW/200mW switchable Antenna Connector: U.FL Baby Ape Camera Model: Darwin205 Resolution: 700TVL Lens: 1.8mm Signal System: PAL/NTSC Baby Ape Pro Camera Model: Caddx Ant Image Sensor: 1/3" CMOS Resolution: 1200TVL Signal System: PAL/NTSC Includes 1x DarwinFPV PNP Baby Ape 3" Quad - Plug-N-Play Choose Version

Read more less

All batteries must be shipped by a ground shipping method. Introducing iFlight's Defender 25, a sub-250 drone featuring the DJI O3 Air Unit. At 249g weight, Defender 25 doesn't require registration in most countries. The compact and lightweight design also make it easy to carry and store. It will be your best travel buddy to redefine your FPV adventure. The built-in 2.5-inch propeller guards were designed to fly boldly. You’ll experience a completely new creative freedom to fly whenever and wherever. The durable injection molded frame not only prevents damage to your motors or propellers but also protects the environment from small flight errors. Equipped with the latest tech from DJI, the O3 Air Unit HD transmission system, the Defender 25 supports 4K video and shoots up to 155° super-wide FOV footage for stunning visuals. In addition, D-Cinelike color mode provides more creative freedom for color grading, allowing you to edit and adjust your footage.  They’ve also added a special vibration-damped camera mount to keep your raw footage as smooth as possible, as well as ensure good Gyro Data for the built-in or in-post camera stabilization. Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products! Features Optimized Landing Gear for Take-Off in Complex Environments Built-in High-Performance video and Receiver Antennas 4K Stabilized Video with 155° Ultra-Wide Angle Crash-Protected Quick-Release Battery Countless Easy-to-Use Features Ultralight and Free to Fly Small and Mighty Specifications Defender 25 Product Name: Defender 25 4S HD Flight Electronics: BLITZ D25 F7 AIO Video Transmission: DJI O3 Air Unit Frame: 112±2mm Motor: Defender25 1404 Prop: Defender25 2525 props (2.5-inch) Weight of the Aircraft: 180g Takeoff Weight incl. 550mAh battery: ≤249g Dimensions (L×W×H)：158x155x69mm Max Ascent Speed: 6 m/s (Normal Mode, Sport Mode) Max Descent Speed: 6 m/s (Normal Mode, Sport Mode) Max Speed: 100Km/H (Manual Mode) Maximum Takeoff Altitude: 200 m Max Hover Time: Approx. 6 mins (with 550mAh battery), 10mins (with 900mAh battery) Max Flight Distance: 2-3 km Max Wind Speed Resistance: 80 Km/H (Level 5) Operating Temperature Range: -10° to 40° C (14° to 104° F) Transmission Power (EIRP): FCC: < 33 dBm / CE: < 14 dBm / SRRC: < 30 dBm Antennas: Dual Antennas GNSS: N/A Video Transmission Product Name: DJI O3 Air Unit Weight: Approx. 36.4grams Dimensions (L×W×H): L16.7×W103.9×H 81.3mm Screen Size (single screen): 0.49-inch Resolution (single screen): 1920×1080 Refresh Rate: Up to 100 Hz Interpupillary Distance Range: 56-72 mm Diopter Adjustment Range: -8.0 D to +2.0 D FOV (single screen): 51° Communication Frequency: 2.400-2.4835 GHz；5.725-5.850 GHz Transmission Power (EIRP): 2.4 GHz: < 30 dBm (FCC), < 20 dBm (CE/SRRC/KC) 5.8 GHz [4]: < 30 dBm (FCC), < 23 dBm (SRRC), < 14 dBm (CE/KC) Max Video Transmission Bitrate: 50 Mbps Operating Temperature Range: 0° to 40° C (32° to 104° F) Power Input: 7-9 V (1.5 A) Recommended (Not Included) iFlight Defender 25 Battery - 900mAh Includes 1x iFlight BNF Defender 25 HD 4S 2.5" Cinewhoop w/ DJI O3 Air Unit and DJI Camera (Pre-Built, Tuned, and Tested) 1x Defender 25 550mAh Battery 1x Charging Adapter Board 2x Defender 25 2525 Props (pairs)

Read more less

The FR16 Nano Baby V2 is an advanced microdrone with improved flight time, power, and appearance over its predecessor. It's 30% more powerful despite being heavier, with flexible flight, great maneuverability, and higher speeds. A newly designed canopy and plate provide crash resistance, and it's equipped with a ROBO 1002 23500KV motor. Plus, the GOKU Versatile F411 ELRS 1S AIO V2 + ELRS 2.4G receiver ensures a lightweight, top-performing design. This version utilizes the elite capabilities of the Walksnail HD digital VTX system.  The Walksnail Avatar HD Mini 1S Lite is a lightweight VTX designed for 1S whoop drones, featuring H.265 high-efficiency video coding technology, 1080P/60FPS image recording with 22ms ultra-low latency, and built-in 8 GB storage for interference-free HD video recording and USB exporting. Check out our other pre-built quads, as well as other great products from Flywoo! Features Redesigned canopy with enhanced aesthetics and reinforced camera protection. The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Equipped with ROBO 1002 23,500KV motor and 1609 4-bladed 40mm propellers, delivers a 30% increase in power, flexible flight, and impressive speeds perfect for racing competitions. The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance.  A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector. New battery compartment design allows for easy replacement of batteries of different models. Specification Motor:  ROBO 1002 23500KV Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0 Props:  1609 - 4 blade 40mm 1.5mm Shaft HD Digital VTX System:  Walksnail Avatar HD Mini 1S Lite Receiver:  ExpressLRS 2.4GHz Weight:  33g Flight Time:  Explorer 1S 450mAh HV V2: 4m - Explorer 1S 750mAh HV V2: 6m (approximate) Speed:  70km/h (approximate) GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller MCU: STM32F411CEU6  GYRO: ICM42688 UARTS: 1/2 Soft serial port: 1 I2C: SCL/SDA BEC: 5V  Input Voltage: 1S (<4.35v) Firmware: FLYWOOF411_5IN1_AIO  Mounting:  25x25mm, M2 Onboard 4in1 ESC MCU: EFM8BB21 Power supply: 1S LiPo/LiPo HVCurrent: 5A  Firmware: BLHeli_S Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT 150/300/600 ELRS 2.4G RX (UART2) Flywoo ROBO 1002 23500KV Fpv Motor: Configuration: 9N12P Stator Diameter: 10mm Stator Length: 2mm Shaft Diameter: 1.5mm Motor Dimension(Dia.xLen): Φ13.5x7.75mm Weight(g): 2.5(5cm wire) Idle current(5)@5V(A): 1.5 No.of Cells(Lipo): 1S Max Continuous Power(W)3S: 52 Internal Resistance: 75mΩ Max Current(3S): 14A Max Efficiency Current: (2-4A)>84% Walksnail Avatar HD Mini 1S Lite Model: Avatar mini 1s module Communication Frequency: 5.725-5.850GHz Transmitter Power (EIRP): FCC:<25.5dBm;CE:<14dBm;SRRC:<20dBm; MIC:<25dBm I/O Interface: JST1.0x6(Power in)JST1.0x4(USB) Mounting Holes: 25.5x25.5mm Dimensions: 30x30x6.5mm Storage: 8G Recording: 1080p/720p Weight: 5.1g Operating Temperature: -20-40℃ Channels: 8 Wide Power Input: 3.1V-5V Supported FC System: Betaflight OSD: Canvas mode Bitrate: 25mbps, 50mbps Latency Average delay: 22ms Antenna: IPEX Avatar lite camera Model: Avatar lite camera Image Sensor: 1/2.7”1nch Resolution: 1080P/60fps,720P/120fps,720P/60fps Ratio: 16/9 4/3 Lens:2.1mm FOV: 170° Aperture: F2.0 Shutter Rolling: Rolling shutter Min.Illumination: 0.001Lux Weight: 1.8g Dimensions: 14x14x16mm  Includes 1x Flywoo BNF Firefly FR16 Nano Baby HD V2.0 1S 1.6" Micro Quad w/ Avatar Nano Cam - ELRS 2.4 GHz 4x 1609 - 4 40mm 1.5mm shaft 2x TPU Battery Mount 1x Hardware Screw Set 4x Prop guards

Read more less

 All products with batteries must be shipped by a ground shipping method. Check out the this BNF Meteor75 Pro HD 1S Brushless Whoop from BETAFPV. This quad is impressive with its clean aesthetic and its down right power performance.  BETAFPV wants you to know this is the largest 1S digital whoop you can get today. This BNF will feature a F4 1S 5A FC, with 1102 22000Kv motors and ideally you would want a 550mAh 1S Battery to use with this quad. With this frame, you will get to see a more roomier battery slot for ease of use, as well as to able to accommodate  a bigger battery.  Note: The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP.  Make sure to check out our other Pre-Built quads and the rest of our BetaFPV selection! Features The upgraded frame that fits 45mm props perfectly makes Meteor75 Pro the largest 1S whoop drone. Powered with 1102 22000KV motors, it performs smoothly in the air and is maneuverable for freestyle tricks. It features a roomier battery slot that can accommodate a bigger battery such as BT2.0 550mAh 1S battery, which provides a larger capacity and higher discharge rate, bringing more flight time and robust flight performance to the quadcopter. Micro Canopy Lite has an adjustable camera lens of 0-40°. This new canopy weighs only 1.1g, which is very suitable for HD digital VTX drone, and the open design makes the electronics cooler better. Equipped with F4 1S 5A flight controller (Serial ELRS 2.4G or SPI Frsky). The ELRS 2.4G RX version comes with the default ELRS V2.0 firmware and supports being upgraded to ELRS V3.0 separately without flashing Betaflight flight controller firmware. The SPI Frsky version can be also used as the PNP version to connect external receiver due to the two UART ports on the board. The various colors of the spare parts including the Meteor75 Pro frame and Micro Reserve two UART ports on F4 1S 5A FC(SPI Frsky) V3.0 board. The Frsky version also can be used as the PNP version. Therefore, pilots can connect the external receiver to it. Ultralight weight for Meteor75 Pro HD 35.77g (Walksnail)/ 34.87g (HDZero), this largest 1S drone combined with Walksnail or HDZero HD digital VTX system gives pilots an immersive flight experience and impactful visuals. HD Digital VTX System The Walksnail Avatar HD Mini 1S Lite uses H.265 high-efficiency video coding, an industry-leading technology, providing 1080P/60FPS image recording with 22ms ultra-low latency. It is specially designed for 3.1-5V power input and 7.8g lightweight, compatible with 1S whoop drone. Built-in 8 GB storage, this VTX has the capability of recording HD video without interference from capacity and exporting video by USB cable. Besides, with Canvas Mode, Betaflight full OSD display is supported and can be adjusted easily by remote control. Note: Please make sure that the battery voltage must be 3.1V at least when flying, otherwise, the HD digital VTX would stop working. Flight Controller The latest F4 1S 5A flight controllers are applied to all BNF versions of Meteor75 HD. It features Serial ELRS 2.4G instead of SPI ELRS 2.4G for ELRS version compared to the previous version. The Frsky version reserves two UART ports for the available external receiver so it can be used as PNP. The ESC on the new board is powered by BB51 hardware in place of BB21. Last but not least, we update the gyro to BOSH BMI270 for better performance and stability since the new F4 1S 5A FC. Meteor75 Pro HD (ELRS) Meteor75 Pro HD (Frsky, PNP, TBS) FC Inside F4 1S 5A FC (Serial ELRS 2.4G) V2.0 F4 1S 5A FC (SPI Frsky) V3.0 Gyro BMI270 BMI270 FC Firmware BETAFPVF411 BETAFPVF411RX UART Port One UART Port Two UART Ports External RX Not Supported Supported Note: Pay attention, ONLY the newest Betaflight firmware 4.3.1 start to support this BMI270 gyrometer. Please check the below link to download the firmware and CLI dump file. If you update the 4.3.1 firmware from Betaflight official site, please flash the CLI dump file for Meteor75 HD. Micro Canopy Lite Micro Canopy Lite is specially designed to be compatible with HD digital VTX and has an adjustable camera lens of 0-40°. By using the new Micro Canopy Lite, the weight of the drone is reduced, which in turn can improve flight performance and increase flight time. The open design helps to dissipate heat more effectively, reducing the risk of damage to the VTX or other electronic components inside the drone. Endurance Boosting Battery With the new BT2.0 550mAh 1S battery, Meteor75 Pro HD ensures more flight time up to 5:30 (Walksnail)/5:40 (HDZero) so that pilots can less worry about the battery. What's more, it has a discharge of 40C (continuous) and 80C (burst), bringing a robust flight experience to pilots. Meteor HD Series BETAFPV has been optimizing and upgrading the Meteor series for better performance. The Meteor HD Series whoop drones including Meteor75 1S HD, and Meteor85 2S HD with Walksnail or HDZero HD digital VTX system aim to provide pilots with an immersive flight experience for FPV racing and high-definition images. Meteor75 Pro Frame Meteor75 Pro frame is the largest 1S whoop frame with 45mm propellers currently and comes with more features. The frame features a roomier battery slot for more battery choices such as BT2.0 550mAh battery. The motor holder is using a triangle bilateral stretch structure, giving pilots a more durable and smoother flight experience. In addition, the Meteor75 Pro frame offers seven colors for options, which pilots should purchase separately. Powerful 1S Drone Combo Even carrying the HD digital VTX system, Meteor75 Pro HD still performs well in power and speed thanks to its upgraded frame that is suitable for 45mm props, allowing it to be the largest 1S power whoop drone with greater thrust and lift. Fit out with 1102 22000KV motors and BT2.0 550mAh 1S battery, this 1S drone combo has an excellent thrust-to-weight ratio performance and provides an immersive flight experience to pilots. Specification Item: Meteor75 Pro Brushless Whoop Quadcopter (1S HD Digital VTX) Flight Time: 5:30 (Walksnail)/ 5:40 (HDZero) Camera Adjustable Angle: 0-40° Motors: 1102 22000KV Motor Battery: BT2.0 550mAh 1S Battery Frame: Meteor75 Pro Brushless Whoop Frame Propellers: Gemfan 45mm 3-Blade Propellers Canopy: BETAFPV Micro Canopy Lite Weight Without Battery: 35.77g (Walksnail)/34.87g (HDZero) Receiver: Serial ELRS 2.4G/SPI Frsky/TBS FC&ESC: F4 1S 5A FC (Serial ELRS 2.4G) V2.0/F4 1S 5A FC (SPI Frsky) V3.0 VTX Power Output: 350mW (Walksnail), 25mW/200mW (HDZero) VTX: Walksnail Avatar HD Mini 1S Lite Kit/HDZero Whoop Lite Bundle Camera: Wanlksnail Avatar Lite Camera/HDZero Nano Lite Camera FAQ Download the FC firmware and CLI dump file for Walksnail and HDZero version. Click to download the manual for Walksnail Avatar HD Mini 1S Lite Kit. Click to download the manual for HDZero Whoop Lite Bundle. Includes 1x BetaFPV BNF Meteor75 Pro 1S Brushless Whoop w/ HDZero & Nano Lite Cam (BT2.0) - Choose Your Receiver 2x BT2.0 550mAh 1S Battery 1x Type-C USB Cable 1x BT2.0 Battery Charger and Voltage Tester 4x 45mm 3-Blade Props (1.5mm Shaft) 1x Screwdriver 1x VTX USB Cable (Walksnail or HDZero Version) 1x Pack of Screws

Read more less

The iFlight Nazgul5 V3 6S 5" Freestyle Analog Quad is here! It includes the RaceCam R1 FPV Camera and Nazgul 5" tri-blade props, XING-E Pro 2207 motors, BLITZ F7 Flight Controller, BLITZ 1000mW+ VTX, and the BLITZ E45S 2-6S 45A BLHeli32 4-in-1 ESC. Boasting CNC aluminum camera mount with vibration-reduction silicone for increased protection. Great for freestyling and long-distance shots with your GoPro camera! The Nazgul5 Freestyle quad is a go-to gold standard for freestyle BNFs of great value made by the great people at iFlight.  The Nazgul5 V3 is a 5" freestyle frame is made of super stiff carbon for minimal resonance. + High-quality parts+ Sturdy frame structure+ Generous mounting space+ Optimized for O3 Air Unit+ GoPro camera mount included  Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products! Features XING-E Pro 2207 motors and NAZGUL F5 props 5" version also fits 5.1" style propellers Fits both 30.5x30.5 and 20x20 stacks 5mm arm design for more durability Popular True-X configuration LED illuminated logo TPU crash-guards Easy-Swap arms Specifications Product Name：Nazgul5 V3 6S Analog FC: BLITZ F722 FC ESC: BLITZ E45S 45A 4-IN-1 ESC Video Transmission: BLITZ 1mW+ VTX Frame: 245 ±2 mm wheelbase Motor: XING-E Pro 2207 motors Prop: Nazgul 5 inch propellers Takeoff Weight: Approx. 435g / 660±10g (With 6S 1400mAh Battery) Dimensions (L×W×H): 173×173×34±2 mm Diagonal Distance: 245mm Max Speed: 190 Km/h (Manual Mode) Maximum Takeoff Altitude: 3200 m Max Hover Time: Approx. 7.5 mins (No Load with 6S 1400mAh Battery) Max Flight Distance: 5 km Max Wind Speed Resistance: Level 7 Operating Temperature Range：-10° to 40° C (14° to 104° F) Antennas: Single Antenna Video Transmission System Product Name: BLITZ Whoop 1mW+ VTX Input voltage: 7V～34V Interface: MMCX Power levels: PIT/25mW/400mW/800mW/1600mW Channels: 40 (including Raceband) Mounting pattern: 30.5x30.5mm/Φ3 Lightweight: 18.9g (excluding antenna) VTX telemetry: IRC Tramp Betaflight IRC Tramp Configuration: Please download the attached VTX table for Betaflight! RC Tramp VTX table values: 25mW/400mW/800mW/1600mW Includes 1x Nazgul5 V3 6S Analog BNF 1x Antennas 2x Battery pads 2x Nazgul F5 Prop(Pairs)

Read more less

Introducing the BOB57, a 6" cinematic long-range quad pre-installed with the all-powerful DJI O3 system for crystal clear image quality. This quad aims to best of 5" and 7", hence the name BOB57. This quad is DJI PNP, meaning it does not come with a receiver, meaning you need to install your receiver.  However, if you have the DJI FPV Remote Controller 2, you can bind to the O3 Air Unit. This quad also comes with a GPS pre-installed, allowing all the marvelous features a GPS allows you. The BOB57 comes with XING2 2506 motors with a rated KV 1500, designed around 6S power.  The iFlight BOB57 is a long-range HD drone that was designed in collaboration with pilot & videographer Ellis van Jason. The team crafted this cinematic 6-inch drone that ensures agility and flight time while combining the advantages of both 5-inch and 7-inch drones for both cinematic and freestyle flights. Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products  Features Hybrid motor design optimized for  that can be used with both bi-blade and tri-blade 6" propellers. High-end GPS is used to minimize the risk of failure during proximity flights Long backbone with enough space up to fit 3000mAh 6S batteries Solid antenna mount for less oscillations when using long antennas Gladiator shell protects from dust and water droplets ESCs with built-in spike absorbers for more reliability Built-in BEC to directly power a GoPro camera 9-minute flight time with 3000mAh 6S Lipo Front-mounting XT-60 DJI O3 Air Unit VERSATILE BODY The Body is designed to carry small to large batteries for agile or long-range missions. SMART XT60 AND USB-C PLUG The XT60 plug is located in the front to gain more space. With the USB-C plug you can directly power your GoPro/Action Cams. OPTIMIZED MOTOR AND PROPS The Motor is designed for 6inch to give both great performance and efficiency. The prop is specifically optimized for this drone. RELIABILITY The BOB57 comes with a shell that protects against hits, droplets, and dust. It also has a high-quality GPS and components for more reliability, like a spike absorber & extra capacitor. PRE-TUNED AND PRE-SETUP Don't worry about tuning, iFlight did that for you already! A basic PID and Filter tuning were applied for a great flight experience! Links Ellis van Jason Tune Setup Specifications Product Name: BOB57 O3 6S HD BNF FC: BLITZ F722 ESC: BLITZ E55 55A 4-IN-1 ESC Video Transmission: DJI O3 Air Unit Frame: 280mm wheelbase Motor: XING2 2506 motors Prop: GEMFAN 6032-3 propellers Takeoff Weight: Approx. 580 g Dimensions (L×W×H)：226×166×34 mm Max Speed: 180 Km/h (Manual Mode) Maximum Takeoff Altitude: 7000 m Max Hover Time: Approx. 8 mins (With 6S 1400 no load.) Max Wind Speed Resistance: Level 7 Operating Temperature Range: -10° to 40° C (14° to 104° F) Antennas: 2 Antenna GNSS: GPS+SBAS+Galileo+QZSS+Glonass Video Transmission  Product Name: DJI O3 Air Unit Weight: Approx. 36.4 grams（headband included） Dimensions (L×W×H): L32.5x W30.5xH 14.5mm Communication Bandwidth： Max 40 MHz FOV (single screen): 155° Communication Frequency: 2.400-2.4835 GHz；5.725-5.850 GHz End-to-End Latency With DJI FPV Goggles V2: 810p/120fps Video Transmission Quality: The latency is lower than 28 ms. 810p/60fps Video Transmission Quality: The latency is lower than 40 ms. With DJI Goggles 2: 1080p/100fps Video Transmission Quality: The latency is as low as 30 ms. 1080p/60fps Video Transmission Quality: The latency is as low as 40 ms. Max Video Transmission Bitrate: 50 Mbps Max Video Transmission Range：10 km (FCC), 2 km (CE), 6 km (SRRC) Operating Temperature Range: -10º to 40º C (14° to 104° F) Power Input: 7.4-26.4 V Audio Transmission: N/A  Includes 1x BOB57 6S HD BNF 2x Antennas 2x Battery pads 2x Prop(Pairs)

Read more less

After our very popular 3-inch Cinematic EVA bumper BumbleBee and Green Hornet CineWhoop series, we were trying to increase performance and reduce weight for an even better and longer flight experience for a wide variety of use.  Our all-new 3.5inch project is finally ready for all you content creators or those guys who like to wear some protection every now and then. Prop protection is what we're talking about here.  ProTek is not necessarily just a Cinewhoop series but far more. Equipped with our all-new 2205 motors for more power and less heat. We were able to increase speed and thrust by 50% compared to its 3inch predecessor which gives a lot more room for a lot more fun. Our GPS-measured maximum speed was above 120km/h and a maximum thrust of 750g per motor (3kg in total) would even carry heavier cams than a Gopro but also do some loaded punch-outs or light freestyle moves.  A lot of thought was put into the different assembly options. Our stock BNF will ship in the standard configuration but you can either do a pusher mod (flip the build upside down) or a lite mod (remove the protective plastic for weight optimization). Be sure to check out our Bind-n-Fly collection as well as all of our iFlight Products! Note: Battery, GoPro, and GoPro mount are NOT included. Check out our other pre-built quads, as well as the rest of our iFlight selection! Features High-performance True-AIO Board Beast Whoop F7 AIO 55A v2.0 to save weight and space T700 Quality Carbon (40% more tensile strength compared to common 3K carbon) Lightweight one-piece frame design (Less flexibility, more Rigid, more Durable) Low Resonance frame construction (Less Jello, more Cinematic footage) Pre-tuned with smooth freestyle settings Butter smooth 2205 3200KV (4S) ProTek35 Prop Guards V2.0 No Props or frame in view! Pre-Tuned & Pre-Setup: Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning were applied for a great flight experience! To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps" Angle-Mode (self-balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess! Please check our linked article on "How to disable Angle-Mode, and activate Acro-Mode" Specifications Beast F7 V2 AIO FC MCU: BGA-STM32F745 Gyro: BMI270 Blackbox: 8Mb Onboard Flash BEC output: 5V 2.5A Barometer: BMP280 Connector: Micro-USB OSD: AT7456E FC Firmware：IFLIGHT_F745_AIO_V2 Mounting pattern: 25.5x25.5mm φ3mm Dimensions: 32.5x32.5mm Weight: 8.5g F7 55A 2-6S ESC Current Sensor: Yes Input: 2-6S LIPO Current scale: 200 Constant: 55A  BLHeli: BLHeli-S Telemetry: no ESC Firmware: BlheliS G-H-30 Mounting pattern: 25.5x25.5mm/Φ3mm Dimensions: 32.5x32.5mm SucceX Mini Force 5.8GHz 600mW VTX Power: PIT/25/200/400mW/600mW Antenna interface: MMCX VTX protocol: IRC Tramp Output 40 channels. Size: 29x29mm Mounting pattern: 20x20Φ3/25x25 mmΦ2 Weight: 4g   Includes 1x ProTek35 Frame 2x Albatross RHCP RP-SMA 5.8g antenna 1x TPU Antenna holder 2x Nazgul 3535 propeller (Set of 4 - Color May Vary) 1x iFlight Lipo Strap 15x150mm (Color May Vary) 1x iFlight Lipo Strap 15x250mm (Color May Vary) 1x GoPro TPU bottom stand black (GoPro Protector not included)

Read more less

For the shooting needs of complex indoor environments, GEPRC has recently released the 2" Cinewhoop CineLog20. Available in Link Wasp, O3 Air Unit, Walksnail, and Analog four mainstream video transmission systems on the market. The CineLog20 continues the CineLog series with a lightweight pusher design, and the redesigned camera gimbal vibration reduction solution provides an excellent mounting platform for O3 AIR Unit shooting, which can achieve an excellent anti-shake effect. The O3 Air Unit version can shoot 4K 60fps video without mounting any camera. It is lighter in weight and has a longer battery life. It adopts GEPRC SPEEDX2 1303.5 5500KV motor and GEP-F411-35A AIO. Equipped with Emax 4-blade propellers, a reasonable and efficient power system makes the CineLog20 very quiet and has a long battery life, making your flight and shooting more assured. Using the one-piece injection molding camera mount, you can quickly mount GEPRC naked GoPro 8/9/10/11 cameras, Action2, insta360 Go2, Peanut, and other light and small action cameras. Find the recommended 4S 450-750mAh batteries here! Check out our other pre-built quads, as well as the rest of our GEPRC selection. Features Designed to mount a shock-absorbing gimbal under the independent FPV camera to reduce jello of FPV Goggles image, with good anti-shake effect. Provide mainstream Link Wasp, O3 AIR Unit, and Walksnail HD video transmission versions, Bind-N-Fly to save the trouble of building and tuning. 2-inch pusher design, small size and lightweight, more suitable for complex and narrow environments flight shooting. SPEEDX2 1303.5 5500KV motor with Emax four-blade propellers make the flight shooting unhurried. Continuing the vibration-dampening structure of the CineLog series, which can effectively eliminate the jello of the image caused by the body when flying with a Naked GoPro mounted. The GEPRC Team’s splendid tuning and overall flight feel are delicate and flexible. Specifications Model: GEPRC BNF Cinelog20 HD 4S 2" Cinewhoop w/ RunCam Wasp & Micro Cam - ELRS 2.4GHz Frame: GEP-CL20 Wheelbase: 100mm Gimbal plate: 2.0mm Top plate: 2.5mm Bottom plate: 1.5mm FC system: GEP-F411-35A AIO MCU: STM32F411CEU6 Gyro: ICM 42688-P OSD: Betaflight OSD w/AT7456E chip ESC: 8Bit 35A VTX: Link Camera: RunCam Wasp Antenna: GEPRC Peano 5.8G LHCP U.FL Motor: GR1303.5 5500KV Propeller: EMAX Avan Micro 2×2.4×4 Receiver: PNP (built-in DJI receiver), ELRS2.4G Recommended battery: LiHv 4S 450mah-660mah Flight time: 4-6min Includes 1x CineLog20 HD Wasp 2x 2-inch propellers (pairs) 1x Naked GoPro Base 2x M15×150mm battery strap 2x Battery Silicone Pads 2x EVA Landing Pads 1x Set of screws 1x L-shaped screwdriver (1.5mm) 1x Antenna fixed tube 1x 4S Naked GoPro power cable (with balanced terminal head) 2x EVA damping rings of guards 1x TBS Antenna mount (Vertical Type) 1x TBS Antenna mount (Horizontal Type) 1x TBS Antenna printed parts The screw package includes: 3x M2×12mm cup head screws 2x M2×5mm round head screws 1x M2×8mm round head screw with pad 3x M2×7mm round head screws 2x M2×8mm round head screws 2x M2 iron nuts 1x self-clinching nut

Read more less

For the shooting needs of complex indoor environments, GEPRC has recently released the 2" Cinewhoop CineLog20. Available in Link Wasp, O3 Air Unit, Walksnail, and Analog the four mainstream video transmission systems on the market. The CineLog20 continues the CineLog series with a lightweight pusher design, and the redesigned camera gimbal vibration reduction solution provides an excellent mounting platform for O3 Air Unit shooting, which can achieve an excellent anti-shake effect. The O3 AIR Unit version can shoot 4K 60fps video without mounting any camera. It is lighter in weight and has a longer battery life. It adopts GEPRC SPEEDX2 1303.5 5500KV motor and GEP-F411-35A AIO. Equipped with Emax 4-blade propellers, a reasonable and efficient power system makes the CineLog20 very quiet and has a long battery life, making your flight and shooting more assured. Using the one-piece injection molding camera mount, you can quickly mount GEPRC naked GoPro 8/9/10/11 cameras, Action2, insta360 Go2, Peanut, and other light and small action cameras. Find the recommended 4S 450-750mAh batteries here! Check out our other pre-built quads, as well as the rest of our GEPRC selection. Features Designed to mount a shock-absorbing gimbal under the independent FPV camera to reduce jello of FPV Goggles image, with good anti-shake effect. Provide mainstream Link Wasp, O3 AIR Unit, and Walksnail HD video transmission versions, Bind-N-Fly to save the trouble of building and tuning. 2-inch pusher design, small size and lightweight, more suitable for complex and narrow environments flight shooting. SPEEDX2 1303.5 5500KV motor with Emax four-blade propellers make the flight shooting unhurried. Continuing the vibration-dampening structure of the CineLog series, which can effectively eliminate the jello of the image caused by the body when flying with a Naked GoPro mounted. The GEPRC Team’s splendid tuning and overall flight feel are delicate and flexible. Specifications Model: GEPRC BNF Cinelog20 HD 4S 2" Cinewhoop w/ Walksnail Avatar & Micro Cam - ELRS 2.4GHz Frame: GEP-CL20 Wheelbase: 100mm Gimbal plate: 2.0mm Top plate: 2.5mm Bottom plate: 1.5mm FC system: GEP-F411-35A AIO MCU: STM32F411CEU6 Gyro: ICM 42688-P OSD: Betaflight OSD w/AT7456E chip ESC: 8Bit 35A VTX: GEPRC 5.8GHz@600mW Camera: Caddx Ratel2 Antenna: GEPRC Peano 5.8G RHCP MMCX Motor: GR1303.5 5500KV Propeller: EMAX Avan Micro 2×2.4×4 Receiver: ELRS2.4G Recommended battery: LiHv 4S 450mah-660mah Flight time: 4-6min Includes 1x CineLog20 Analog 2x 2-inch propellers (pairs) 1x Naked GoPro Base 2x M15×150mm battery strap 2x Battery Silicone Pads 2x EVA Landing Pads 1x Set of screws 1x L-shaped screwdriver (1.5mm) 1x Antenna fixed tube 1x 4S Naked GoPro power cable (with balanced terminal head) 2x EVA damping rings of guards 1x TBS Antenna mount (Vertical Type) 1x TBS Antenna mount (Horizontal Type) 1x TBS Antenna printed parts The screw package includes: 3x M2×12mm cup head screws 2x M2×5mm round head screws 1x M2×8mm round head screw with pad 3x M2×7mm round head screws 2x M2×8mm round head screws 2x M2 iron nuts 1x self-clinching nut

Read more less

Flywoo's Firefly Hex Nano V1.2 is the smallest hexacopter ever designed by Flywoo, weighing in at 74g. It powerfully and stably carries Insta 360go and SMO 4K cameras. The Firefly hex nano is small, flexible, stable, and is full of power and offers unmatched control. Check out our other pre-built quads, as well as other great products from Flywoo! Feature Hexacopter HD system Naked Vista Weighing only 74 grams Built in SMO Power Cable Prebuilt and tested Specifications Weight: 74g Wheelbase: 80mm FC & ESC:【No.C203】GOKU HEX F4 16x16 STACK - ( FC+13A ESC ) ( MPU6000) Frame: Firefly Baby Quad Frame (HD Verison) Motors: Nin V2 1203Pro 5500Kv Props: Gemfan 1636 40mm-4 V2.0 HD digital camera & VTX: Naked RunCam Link & RunCam Wasp Antenna: Atomic 5.8GHz Antenna Length 30mm (LHCP) Battery (Recommended): 4S 450mAh / 4S 300mAh battery (Not including) GOKU HEX GN405 Nano16X16 FC  MCU: STM32F405 BGA IMU: ICM42688P Barometer: DPS310 input voltage： 2-6S Onboard LED：WS2812x4 6 hardware UARTS (UART1,2,3,4,5,6) Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported. Onboard 16Mbytes for Blackbox logging 5V Power Out: 2.0A max 3.3V Power Out: 0.5A max Dimensions: 22x22mm Mounting Holes: 16x16mm Weight: 2.3g Firmware : FLYWOOF405NANO BS13A BLheli_S 2-4S 4in1 lBS20/35A BLheli_S 2-6S 4in1 Weight: 2.5g Mounting Hole: 16x16mm (M3) Support Oneshot, Multishot, DShot150/300/600 Nin V2 Motor Stator Size: 1203 Motor Bolt Pattern: 9x9mm KV: 5500 Wasp Nano HD Camera Dimensions: L18mmxW14mmxH18mm LENS: FOV D:160° H:127° V:92° Resolution: 720P@120fps(4:3) Net Weight: 6g(With Cable) Shutter: Rolling Shutter Coaxial Cable: 80 mm Image Sensor: 1/3" Naked Link Air Unit Input Voltage: 7.4-26.4V@ 4-9W Operating Frequency: 5.725-5.850 GHz Transmitter Power: (EIRP) FCC/SRRC: <30 dBm; CE: <14 dBm Min. Latency (end-to-end): 1280 x 720 60fps: 32 ms Max. Transmission Distance: FCC/SRRC: 4 km; CE: 0.7 km; I/O Interface: Type-C, IPEX, 3-in-1 port, Supported Flight Control System: BetaFlight Operating Temperature Range: 0° to 40° C (32° to 104° F) Includes 1x Flywoo BNF Firefly Hex Nano V1.2 1.6" HD 4S Micro Quad w/ Naked RunCam Link & RunCam Wasp - Choose Receiver 1x Accessories (props, prop guard, RunCam link shell, battery straps, hardware, ect)

Read more less