The FR16 Nano Baby V2 is a meticulously crafted microdrone with improved appearance, flight time, and power compared to its predecessor. Power has increased by 30%, with flexible flight, exceptional maneuverability, and higher speeds. A new canopy reinforces camera protection, while a new bottom plate adds sturdiness and crash resistance. The drone is equipped with a special gold-purple edition ROBO 1002 23,500KV motor and GOKU Versatile F411 VTX 1S AIO V2 with 250mW video transmitter. The Flywoo 1S Nano camera V3 delivers clearer and better image quality on this quad. Check out our other pre-built quads, as well as other great products from Flywoo! Features Redesigned canopy with enhanced aesthetics and reinforced camera protection. The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Equipped with ROBO 1002 23,500KV motor and 1609 4-bladed 40mm propellers, delivering a 30% increase in power, reduced noise, and enhanced flight stability. Ultra-light GOKU Versatile F411 1S VTX AIO V2 with upgraded circuit board stability and a 250mw video transmitter, enabling an extended flight range. A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector. Upgraded Flywoo 1S Nano camera V3 delivers clearer and better image quality. New battery compartment design allows for easy replacement of batteries of different models. Specification Motor:  ROBO 1002 23500KV Electronics:  GOKU Versatile F411 VTX 1S 5A AIO V2.0 w/250mW VTX Props:  1609 - 4 blade 40mm 1.5mm Shaft Camera:  Flywoo 1S Nano Camera V3 Receiver:  ExpressLRS 2.4GHz Weight:  26g Flight Time:  Explorer 1S 450mAh HV V2: 4m - Explorer 1s 750mAh HV V2: 6m (approximate) Speed:  80km/h (approximate) GOKU Versatile F411 VTX 1S 5A AIO V2.0 w/ 250mw VTX Flight Controller MCU: STM32F411CEU6  GYRO: ICM42688 UARTS: 1/2 Soft serial port：1 I2C: SCL/SDA BEC: 5V  Input Voltage: 1S (<4.35v) Firmware: FLYWOOF411_5IN1_AIO  Mounting:  25x25mm, M2 Onboard 4in1 ESC MCU: EFM8BB21 Power supply: 1S LiPo/LiPo HV Current: 5A  Firmware: BLHeli_S Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT 150/300/600 Onboard 5.8g VTX Output power: 25mw~250mw switchable Frequency: 40CH Frequency: 5.8GHz 5 bands 40 channels(include Race band) IRC ready Flywoo ROBO 1002 23500KV Fpv Motor: Configuration: 9N12P Stator Diameter: 10mm Stator Length: 2mm Shaft Diameter: 1.5mm Motor Dimension(Dia.xLen): Φ13.5x7.75mm Weight(g): 2.5(5cm wire) Idle current(5)@5V(A): 1.5 No.of Cells(Lipo): 1S Max Continuous Power(W)3S: 52 Internal Resistance: 75mΩ Max Current(3S): 14A Max Efficiency Current: (2-4A)>84% Flywoo 1S Nano Camera V3 Model: Flywoo 1S Nano Camera V3 Image Sensor: 1/3" CMOS Sensor Horizontal Resolution: 1200 TVL TV System: NTSC and PAL(switchable) MENU: Support IMAGE: 4:3 Synchronization: Internal Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio: >52dB (AGC OFF) Video Output: CVBS Lens: 1.8mm/F2.5 Min. illumination: 0.001Lux Auto Gain Control: YES BLC: YES WDR: Global WDR DNR: 3D DNR Dimensions: 14x14mm Wide Power Input: DC 3.7-18V Work Temperature: -20°C~+60C Work Humidity: 20%~80% Weight: 2.1g Includes 1x Flywoo BNF Firefly FR16 Nano Baby Analog V2.0 1.6" 1S Micro Quad - ELRS 2.4 GHz 4x 1609 - 4 40mm 1.5mm shaft 2x TPU Battery Mount 1x Hardware Screw Set 4x Prop guards

Read more less

The props for this BNF press fit on and do not screw into the motor (much like many other Whoops & Toothpicks) The only difference between the Baby Ape and Baby Ape Pro versions is the camera. Darwin FPV is coming in hot with this affordable new 3" quad. Finding a good quad at a decent price is almost impossible these days but DarwinFPV has done it with this little ripper! Make sure to check out all of our BNF quads as well as the rest of our DarwinFPV selection! Specifications Motors Input Voltage: 1-3S Stator Size: 11x4mm KV: 4300 AIO MCU: STM32F411 Gyro: MPU6000 BEC: 5V/2A,3.3V Input voltage: 1-3S Lipo Support Receiver: PPM, Ibus, Sbus, Dsmx Black box: NO Barometer: NO Firmware: MATEKF411 Buzzer interface: YES Betaflight OSD: AT7456E Constant current: 15A Peak current: 17A MCU: EFM8BB21F16G(48MHz) Firmware: BLHeli_S Protocol: Dshot600 Mounting: 25.5X25.5 M2 VTX Input Voltage: 7V~24V RF Output Power: 0mW/25mW/100mW/200mW switchable Antenna Connector: U.FL Baby Ape Camera Model: Darwin205 Resolution: 700TVL Lens: 1.8mm Signal System: PAL/NTSC Baby Ape Pro Camera Model: Caddx Ant Image Sensor: 1/3" CMOS Resolution: 1200TVL Signal System: PAL/NTSC Includes 1x DarwinFPV PNP Baby Ape 3" Quad - Plug-N-Play Choose Version

Read more less

The FR16 Nano Baby V2 is an advanced microdrone with improved flight time, power, and appearance over its predecessor. It's 30% more powerful despite being heavier, with flexible flight, great maneuverability, and higher speeds. A newly designed canopy and plate provide crash resistance, and it's equipped with a ROBO 1002 23500KV motor. Plus, the GOKU Versatile F411 ELRS 1S AIO V2 + ELRS 2.4G receiver ensures a lightweight, top-performing design. This version utilizes the elite capabilities of the Walksnail HD digital VTX system.  The Walksnail Avatar HD Mini 1S Lite is a lightweight VTX designed for 1S whoop drones, featuring H.265 high-efficiency video coding technology, 1080P/60FPS image recording with 22ms ultra-low latency, and built-in 8 GB storage for interference-free HD video recording and USB exporting. Check out our other pre-built quads, as well as other great products from Flywoo! Features Redesigned canopy with enhanced aesthetics and reinforced camera protection. The bottom plate is thicker and has extended motor protection corners, resulting in a more stable and durable quadcopter. Equipped with ROBO 1002 23,500KV motor and 1609 4-bladed 40mm propellers, delivers a 30% increase in power, flexible flight, and impressive speeds perfect for racing competitions. The GOKU Versatile F411 ELRS 1S AIO V2 boasts an ELRS 2.4G receiver, expertly connected via UART 2 instead of SPI for superior performance.  A30 plug supports a continuous current of 15A, providing greater power and longer flight times compared to the PH2.0 connector. New battery compartment design allows for easy replacement of batteries of different models. Specification Motor:  ROBO 1002 23500KV Electronic: GOKU Versatile F411 ELRS 1S 5A AIO V2.0 Props:  1609 - 4 blade 40mm 1.5mm Shaft HD Digital VTX System:  Walksnail Avatar HD Mini 1S Lite Receiver:  ExpressLRS 2.4GHz Weight:  33g Flight Time:  Explorer 1S 450mAh HV V2: 4m - Explorer 1S 750mAh HV V2: 6m (approximate) Speed:  70km/h (approximate) GOKU Versatile F411 ELRS 1S 5A AIO V2.0Flight Controller MCU: STM32F411CEU6  GYRO: ICM42688 UARTS: 1/2 Soft serial port: 1 I2C: SCL/SDA BEC: 5V  Input Voltage: 1S (<4.35v) Firmware: FLYWOOF411_5IN1_AIO  Mounting:  25x25mm, M2 Onboard 4in1 ESC MCU: EFM8BB21 Power supply: 1S LiPo/LiPo HVCurrent: 5A  Firmware: BLHeli_S Factory firmware: O_H_5_REV16_8.HEX Default protocol: DSHOT 150/300/600 ELRS 2.4G RX (UART2) Flywoo ROBO 1002 23500KV Fpv Motor: Configuration: 9N12P Stator Diameter: 10mm Stator Length: 2mm Shaft Diameter: 1.5mm Motor Dimension(Dia.xLen): Φ13.5x7.75mm Weight(g): 2.5(5cm wire) Idle current(5)@5V(A): 1.5 No.of Cells(Lipo): 1S Max Continuous Power(W)3S: 52 Internal Resistance: 75mΩ Max Current(3S): 14A Max Efficiency Current: (2-4A)>84% Walksnail Avatar HD Mini 1S Lite Model: Avatar mini 1s module Communication Frequency: 5.725-5.850GHz Transmitter Power (EIRP): FCC:<25.5dBm;CE:<14dBm;SRRC:<20dBm; MIC:<25dBm I/O Interface: JST1.0x6(Power in)JST1.0x4(USB) Mounting Holes: 25.5x25.5mm Dimensions: 30x30x6.5mm Storage: 8G Recording: 1080p/720p Weight: 5.1g Operating Temperature: -20-40℃ Channels: 8 Wide Power Input: 3.1V-5V Supported FC System: Betaflight OSD: Canvas mode Bitrate: 25mbps, 50mbps Latency Average delay: 22ms Antenna: IPEX Avatar lite camera Model: Avatar lite camera Image Sensor: 1/2.7”1nch Resolution: 1080P/60fps,720P/120fps,720P/60fps Ratio: 16/9 4/3 Lens:2.1mm FOV: 170° Aperture: F2.0 Shutter Rolling: Rolling shutter Min.Illumination: 0.001Lux Weight: 1.8g Dimensions: 14x14x16mm  Includes 1x Flywoo BNF Firefly FR16 Nano Baby HD V2.0 1S 1.6" Micro Quad w/ Avatar Nano Cam - ELRS 2.4 GHz 4x 1609 - 4 40mm 1.5mm shaft 2x TPU Battery Mount 1x Hardware Screw Set 4x Prop guards

Read more less